Registration Test Quiz Fse #10

14 Questions | Total Attempts: 35

SettingsSettingsSettings
Please wait...
Registration Test Quiz Fse #10

Questions and Answers
  • 1. 
    The engineering design report must not exceed how many pages?
    • A. 

      6

    • B. 

      8

    • C. 

      9

    • D. 

      4

  • 2. 
    What is an element of the Statics at FSG?
    • A. 

      Design Spec Sheet (DSS)

    • B. 

      Break Even Cost Table (BECT)

    • C. 

      Business Logic Case (BLC)

    • D. 

      Failure Mode and Effects Analysis

  • 3. 
    What is rule FSAE EV3.6.3 about?
    • A. 

      Accumulator Cell Temperature Measurement

    • B. 

      Ready-To-Drive-Sound

    • C. 

      Accumulator Cell Voltage Measurement

    • D. 

      Accumulator Cell Voltage Sense Wire Fusing

    • E. 

      Galvanic Isolation of the AMS

  • 4. 
    In order to have a protest considered, a team must post a point protest bond which will be forfeited if their protest is rejected. How high is this bond?
    • A. 

      25 Points

    • B. 

      30 Points

    • C. 

      35 Points

    • D. 

      40 Points

    • E. 

      50 Points

    • F. 

      10 Points

  • 5. 
    The included angle formed by the Main Hoop and the Main Hoop braces must be at least...
    • A. 

      Thirty degrees (30°).

    • B. 

      Twenty five degrees (25°).

    • C. 

      Thirty five degrees (35°).

    • D. 

      Thirty two degrees (32°).

    • E. 

      Twenty degrees (20°).

  • 6. 
    Which is the exact resistance value for the IMDT for a vehicle with a system voltage of 458V?
    • A. 

      110.5 kOhm

    • B. 

      112.5 kOhm

    • C. 

      114.5 kOhm

    • D. 

      116.5 kOhm

  • 7. 
    On all cars, a X solid steel or Y solid aluminum "anti-intrusion plate" must be integrated into the Impact Attenuator.
    • A. 

      X = 1.5 mm (0.060 in) and Y = 4.0 mm (0.157 in)

    • B. 

      X = 1.2 mm (0.047 in) and Y = 4.0 mm (0.157 in)

    • C. 

      X = 1.5 mm (0.060 in) and Y = 3.5 mm (0.138 in)

    • D. 

      X = 1.2 mm (0.047 in) and Y = 3.5 mm (0.138 in)

  • 8. 
    A racecar is going through a left corner with Radius 20m at a velocity of 50 km/h. Additionally the brakes generate a deceleration of 7,5 m/s^2. The Rollcenter height of the car is 20mm and the COG is located 300mm above the Rollcenter. The weight and the Roll stiffness distribution is both 50%, track width is 1,3m and the wheelbase value is 1,7m. The mass of the car is 350kg with driver.Round on the second digit behind the point.Which is the right wheel load distribution?
    • A. 

      FR=1521,13 FL=689,75 RR=1027,01 RL=195,63

    • B. 

      FR=1525,91 FL=689,96 RR=1026,79 RL=195,84

    • C. 

      FR=1525,91 FL=689,96 RR=1026,79 RL=185,84

    • D. 

      FR=1525,91 FL=699,96 RR=1026,79 RL=195,84

    • E. 

      FR=1525,91 FL=899,96 RR=1026,79 RL=195,84

    • F. 

      FR=1525,91 FL=699,96 RR=1026,79 RL=395,84

    • G. 

      FR=1325,91 FL=699,96 RR=1226,79 RL=395,84

    • H. 

      FR=1725,91 FL=499,96 RR=1026,79 RL=395,84

  • 9. 
    Which value has the quotient of Front Brake Force to Rear Brake Force for a car with a wheelbase of 1600mm, a weight distribution of 55%, a COG height of 300mm and tires with a constant µ of 1,4?It is assumed that the car is set up at ideal brake balance.Round on the first digit behind the point. 
    • A. 

      2.5

    • B. 

      3

    • C. 

      1

    • D. 

      1.7

    • E. 

      4

    • F. 

      0

    • G. 

      2.8

    • H. 

      1.8

    • I. 

      7

    • J. 

      -2

  • 10. 
    You are pushing an electric Formula Student vehicle around. The grounded low voltage system (GLVS) is turned on while the tractive system is offline. The overall gear-ratio from your drivetrain is 21 and the wheel diameter 450mm. How fast you will have to push your car to obtain a flashing TSAL, if your motor induces 670V at 30000rpm.
    • A. 

      10,85 km/h

    • B. 

      7,23 km/h

    • C. 

      4,58 km/h

    • D. 

      12,76 km/h

    • E. 

      35,21 km/h

    • F. 

      17,32 km/h

    • G. 

      8,32 km/h

    • H. 

      11,61 km/h

    • I. 

      It won't flash, because the tractive system is offline

    • J. 

      It is always flashing, when pushing the car around with activated GLVS

  • 11. 
    Which of the following answers is wrong?
    • A. 

      Before the Acceleration Event you are allowed to take a Flap off the car

    • B. 

      Before the Acceleration Event you are allowed to take a shim off the upright to adjust camber.

    • C. 

      Before the Acceleration Event you are allowed to replace the seat insert

    • D. 

      Before the Acceleration Event you are allowed to swap your brake pads

  • 12. 
    Which of the answers below is wrong?
    • A. 

      The Formula SAE® event is a design engineering competition and is NOT a race.

    • B. 

      In the event of unsportsmanlike conduct a second violation will result in expulsion of the team from the competition.

    • C. 

      Failure of a team member to follow an instruction or command directed specifically to that team or team member will result in a twenty five (25) point penalty.

    • D. 

      Argument with, or disobedience to, any official may result in the team being eliminated from the competition.

    • E. 

      Alcohol, illegal drugs, weapons or other illegal material are prohibited on the event site. Any violation of this rule by a team member will cause the expulsion of the entire team.

    • F. 

      In the interest of responsible citizenship it is expected that any disruptive parties, either on or off-site, will be prevented by the Faculty Advisor.

    • G. 

      Teams which do not obey to reservation of place of other teams on the campsite will not be allowed to come on the campsite in the next season anymore

  • 13. 
    Which of the following answers about fire extinguishers is not correct for FSE?
    • A. 

      You need to have 2 fire extinguishers with a minimum content of 0,9kg.

    • B. 

      The minimum acceptable rating is 34B or 5A 34B

    • C. 

      Once they are inspected, one extinguisher must accompany the car and one has to stay in the teams paddock

    • D. 

      A car internal Halon extinguisher system can replace the extinguisher that accompanies the car

  • 14. 
    Which of these items do not have to be brought to Technical Inspection?
    • A. 

      The ESA

    • B. 

      Two Pairs of HV Gloves

    • C. 

      SES

    • D. 

      Technical Inspection Sheet

    • E. 

      Fire extinguishers

    • F. 

      All drivers

Back to Top Back to top