Tanay 1

10 Questions | Total Attempts: 23

SettingsSettingsSettings
Please wait...
Church Quizzes & Trivia

Tanay1


Questions and Answers
  • 1. 
    The upper and lower members of the front bulkhead is 180mm and 150mm respectively and use a standard I.A. 
    • A. 

      We will need a diagonal brace of tube of dimension 1.00"X0.049"

    • B. 

      We will need a X brace of tube of dimension 1.00"X0.049"

    • C. 

      Insufficient information

    • D. 

      Options 1 & 2

  • 2. 
    What is the minimum thread depth of a wet tyre ?
    • A. 

      2.3 mm

    • B. 

      None of these

    • C. 

      2.1 mm

    • D. 

      3/34"

  • 3. 
    A car is going around a corner of constant radius of 34m. What speed does it need go around to show sufficient roll-over stability ?
    • A. 

      80.567 km/hr

    • B. 

      86.5 km/hr

    • C. 

      79.45 km/hr

    • D. 

      83.567 km/hr

  • 4. 
    At what pressure is a hydraulic line considered a high pressure line ?
    • A. 

      300 psi

    • B. 

      250 psi

    • C. 

      350 psi

    • D. 

      320 psi

  • 5. 
    Of what thickness should a shield be made for the fore-mentioned high pressure lines ? 
    • A. 

      0.1 mm steel

    • B. 

      0.4mm aluminium

    • C. 

      0.4 mm steel

    • D. 

      0.1 mm aluminium

    • E. 

      Not required

  • 6. 
    Tick the correct options with respect to jacking points.
    • A. 

      The jacking point is 210mm above the ground when the wheels are 15mm above the ground

    • B. 

      The jacking point is 60 mm above the ground when the car has 15 mm of jounce

    • C. 

      The length of the jacking bar is 280 mm

    • D. 

      O.d. is 26 mm

  • 7. 
    The test rpm for a engine with stroke length 300mm
    • A. 

      1900 rpm

    • B. 

      2000 rpm

    • C. 

      4500 rpm

    • D. 

      1500 rpm

  • 8. 
    Which the following would pass the technical inspection?
    • A. 

      The distance between shoulder harness points is 220 mm

    • B. 

      The shoulder harness attachment point is sheared in at 61.23 sq.in

    • C. 

      The thickness of a Y-type shoulder strap is 3"

    • D. 

      The harness is mounted on a bent tube and can bear 7kN per attachment

  • 9. 
     With regarding the the front bulkhead the following would pass the inspection. 
    • A. 

      The upper support member is attached at 2" below the top of the front bulkhead

    • B. 

      The upper support member is 5" above upper side impact member attachment point

    • C. 

      Its made of steel tubing of 1"X0.095"

    • D. 

      Diagonal brace is of 1"X0.065"

  • 10. 
    Tick the correct statements
    • A. 

      Scatter shields for chains are made of 2.65 mm thick steel

    • B. 

      For a plastic belt drive aluminium shield of 2 mm thickness is used

    • C. 

      For a plastic belt drive the thickness is 1.7 times the width of the belt

    • D. 

      Fasteners are of 8 mm metric grade 8.8