FSG Quiz #3 - 15.12.2015

10 Questions | Total Attempts: 66

SettingsSettingsSettings
Please wait...
FSG Quiz #3 - 15.12.2015

.


Questions and Answers
  • 1. 
    Which certificate must the required driver's underclothing have to have, to be permitted at FSG?
    • A. 

      SFI 3.3 or FIA 8856-2000

    • B. 

      SFI 3.2

    • C. 

      SFI 3.3

    • D. 

      FIA Standard 1986

  • 2. 
    The fuel filler neck on your car is angled at 28 degrees from the vertical, the clear sight tube is installed parallely to the fuel filler neck. How long does it have to be?
    • A. 

      110.39

    • B. 

      84.95

    • C. 

      141.57

    • D. 

      66.22

  • 3. 
    Your motorcycle engine has a stroke of 42.5mm, at which rpm will the noise test be measured?
    • A. 

      10.758 1/min

    • B. 

      21.516 1/min

    • C. 

      6500 1/min

    • D. 

      Maximum engine rpm

    • E. 

      Idle rpm

  • 4. 
    Which reason of disqualification in the Endurance event is especially mentioned in the rules?
    • A. 

      Low oil pressure in left corners

    • B. 

      An ugly driver

    • C. 

      Tires with a very low grip level

    • D. 

      Kicking more than 5 cones in a row

    • E. 

      A malfunctioning brake light

  • 5. 
    The baseline steel property for the Yield Strength (Sy) that is used for calculations of bending and buckling strength in an SES may not be lower than
    • A. 

      300 MPa

    • B. 

      365MPa

    • C. 

      200GPa

    • D. 

      305MPa

    • E. 

      180MPa

    • F. 

      360MPa

    • G. 

      370Mpa

    • H. 

      400Gpa

  • 6. 
    Which statement about requirements for camera mounts is wrong?
    • A. 

      Helmet mounted cameras and helment camera mounts are prohibited.

    • B. 

      All camera installations must be approved at Technical Inspection.

    • C. 

      The body of a camera or recording unit that weights more than 0.25kg must be secured at a minimum of 2 points on different sides of the camera body.

    • D. 

      The camera mount must withstand a 20g impact in lonitudinal direction. This must be proven in the SES.

    • E. 

      The mounts for video/photographic cameras must be of a safe and secure design.

  • 7. 
    Which of these measures is not used to dimension the cockpit internal cross section template?
    • A. 

      7mm

    • B. 

      350mm

    • C. 

      75mm

    • D. 

      50mm

  • 8. 
     Your car is equipped with a front and rear DRS, it is being pushed from the pit to the dynamic area by 2 team members at the pushbar. What is a true statement?
    • A. 

      Because of a rule violation you will be moved to the end of the Endurance Queue

    • B. 

      Everything is okay.

    • C. 

      You get a 10 point penalty due to rule violation

    • D. 

      You get a 25 point penalty due to a rule violation

  • 9. 
    To prevent fuel and other liquids from pooling in closed structures of your car, it has to feature:
    • A. 

      2 drain holes, at least 25,4 mm in diameter

    • B. 

      2 drain holes, at least 25 mm in diameter

    • C. 

      A single drain hole, with no specific size

    • D. 

      A single drain hole, at least 30mm in diameter

  • 10. 
    A cell stack is built in a 20s3p configuration. These cells have a nominal voltage of 3.7V and a maximum voltage of 4.2V. The nominal capacity of a single cell is 5Ah, while the maximum capacity is 5.3Ah. What is the contained energy of the cell stack according to the inter-cell-stack firewall regulations?
    • A. 

      4808kJ

    • B. 

      4236kJ

    • C. 

      4536kJ

    • D. 

      3996kJ

Back to Top Back to top