Aswin - Govind Quiz1
- 1.
Write your text here
- 2.
Which of the following codes belong to the formula student Lincoln ?
- A.
FSAEL
- B.
FSL
- C.
SFL
- D.
FSAEE
- E.
BOTH FSAEE AND FSAEL
- F.
NONE. THIS EVENT IS NOW DEFUNCT .
Correct Answer
E. BOTH FSAEE AND FSAELExplanation
The correct answer is BOTH FSAEE AND FSAEL. This means that both the codes FSAEE and FSAEL belong to the Formula Student Lincoln event.Rate this question:
-
- 3.
Bolts used in sleeve joints
- A.
8mm 8.8 grade
- B.
8mm 9.8grade
- C.
6mm 8.8 grade
- D.
6mm 9.8 grade
- E.
4mm 8.8 grade
- F.
4mm 9.8 grade
Correct Answer
C. 6mm 8.8 gradeExplanation
The correct answer is 6mm 8.8 grade. This is because when selecting bolts for sleeve joints, it is important to consider the appropriate size and strength. In this case, the 6mm bolt is the appropriate size for the sleeve joint. The 8.8 grade indicates a high tensile strength, making it suitable for applications that require a strong bolt. Therefore, the 6mm 8.8 grade bolt is the best choice for sleeve joints.Rate this question:
-
- 4.
Dollies are used in FSG for
- A.
Protection of the car overnight
- B.
To ship them after the event from the track
- C.
To clear the car off the course; should it stop during the event
- D.
For tilt test
- E.
For noise test
- F.
Its not used in any event , except FSAEL
Correct Answer
C. To clear the car off the course; should it stop during the eventExplanation
Dollies are used in FSG to clear the car off the course if it stops during the event. This means that if the car breaks down or stops functioning during the event, dollies are used to remove it from the track. This ensures that the course remains clear and the event can continue without any obstructions.Rate this question:
-
- 5.
Find the ratio of the area of the cockpit opening template to the minimum head restraint area
- A.
10.0
- B.
11.02
- C.
12.02
- D.
13.03
- E.
14.04
- F.
15.05
Correct Answer
C. 12.02Explanation
The ratio of the area of the cockpit opening template to the minimum head restraint area is 12.02.Rate this question:
-
- 6.
ROLL OVER STABILITY IS MEASURED BY KEEPING THE CAR ON THE TILT TABLE AND ROTATING IT :
- A.
30 DEG TO THE HORIZONTAL , CORRESPONDING TO 1.7 G
- B.
30 DEG TO HORIZONTAL , CORRESPONDING TO 2.0 G
- C.
30 DEG TO HORIZONTAL , CORRESPONDING TO 1.6G
- D.
60 DEGREES TO HORIZONTAL , CORRESPONDING TO 1.7 G
- E.
60 DEG TO VERTICAL , CORRESPONDING TO 1.70G
- F.
30 DEG TO HORIZONTAL , CORRESPONDING TO 1.5 G
Correct Answer
D. 60 DEGREES TO HORIZONTAL , CORRESPONDING TO 1.7 GExplanation
Roll over stability is measured by keeping the car on a tilt table and rotating it to different angles. The correct answer is "60 DEGREES TO HORIZONTAL, CORRESPONDING TO 1.7 G" because this specific angle and corresponding gravitational force (1.7 G) provide the most accurate measurement of the car's stability in a rollover situation. This angle and force combination likely represents the maximum limit at which the car can maintain its stability without tipping over.Rate this question:
-
- 7.
What is the minimum second moment of area of roll hoop bracing if made from steel tube
- A.
6695m^4
- B.
6695e-9m^4
- C.
6695*10^-4m^4
- D.
695e-9m^4
- E.
11320e-9m^4
- F.
11320*10^-4m^4
Correct Answer
D. 695e-9m^4Explanation
The minimum second moment of area of roll hoop bracing is 695e-9m^4. This means that the roll hoop bracing made from steel tube has a very small resistance to bending. The smaller the second moment of area, the more flexible the structure is, which can be beneficial in certain applications where flexibility is desired.Rate this question:
-
- 8.
In an upright driving position the difference between the maxima and the minima of the angle the lap belt must be is ______________
- A.
20
- B.
15
- C.
45
- D.
85
- E.
80
- F.
30
Correct Answer
A. 20Explanation
In an upright driving position, the difference between the maxima and the minima of the angle the lap belt must be is 20. This means that the lap belt should be positioned at an angle that is 20 degrees higher or lower than the average angle when driving in an upright position. This allows for flexibility and adjustment to accommodate different body shapes and sizes while still ensuring proper restraint and safety.Rate this question:
-
- 9.
Any tubing with a wall thickness lesser than __________ is considered non structural
- A.
1.2mm
- B.
1.4mm
- C.
2mm
- D.
4.5mm
- E.
1.6mm
- F.
1.8mm
Correct Answer
A. 1.2mmExplanation
Any tubing with a wall thickness lesser than 1.2mm is considered non-structural because it does not have enough strength to support a structural load.Rate this question:
-
- 10.
What is the area of the hole present at the non critical points of both the roll hoops
- A.
56.58mm^2
- B.
59.5mm^2
- C.
61.58mm^2
- D.
63.58mm^2
- E.
64.58mm^2
- F.
65.88mm^2
Correct Answer
D. 63.58mm^2 -
- 11.
A vertical steering column has two moments of inertia (i.e. Ixx and Iyy ). The column will tend to buckle in the direction of the
- A.
Axis of load
- B.
Perpendicular to the axis of load
- C.
Maximum moment of inertia
- D.
Minimum moment of inertia Minimum moment of inetia Minimum moment of inetia
- E.
No affect
Correct Answer
D. Minimum moment of inertia Minimum moment of inetia Minimum moment of inetiaExplanation
The correct answer is "Minimum moment of inertia". The column will tend to buckle in the direction of the minimum moment of inertia. This is because the minimum moment of inertia represents the axis of the column that is the weakest and most susceptible to buckling under load.Rate this question:
-
- 12.
Team x showed up for FSG 2017 held in hockenheim racing circuit .they were reviewed for part content . the feasibility of their manufacturing design was also gone through . All the necessary documents were submitted and assessed. The accuracy of the cost information was also scrutinized . How many points will they receive if the judges decide they should only be awarded 80 percent of the maximum point s?
- A.
24
- B.
40
- C.
30
- D.
38
- E.
35
- F.
32
Correct Answer
F. 32Explanation
The team will receive 32 points if the judges decide they should only be awarded 80 percent of the maximum points. This means that they are being given 80 percent of the total possible points, which is calculated by multiplying the maximum points by 0.8. Therefore, 40 (maximum points) multiplied by 0.8 equals 32.Rate this question:
-
- 13.
According to the FSAE 2017/18 rule book which of the following events may receive a maximum points update :Engineering design a1.Endurance 2.Skidpad3.Efficiency4.Autocross5.Presentation6.Accelaration
- A.
1,2,3,4&5
- B.
1,3,5
- C.
2,3
- D.
1,6
- E.
1&4
- F.
2,4
Correct Answer
E. 1&4Explanation
According to the FSAE 2017/18 rule book, the events that may receive a maximum points update are Engineering design and Autocross.Rate this question:
-
- 14.
Team X went for participated in the autocross event, but was unhappy with the result.They held a meeting within the team and decided to complain and went 47 minutes after the results were published
- A.
Points increased
- B.
Points decreased due to late approach
- C.
No change because team is not allowed to question the result
- D.
Allowed to participate in the event next day
- E.
Extra points were awarded in some other event to compensate
- F.
None of theese
Correct Answer
F. None of theese -
- 15.
A german Team participating in FSG 2017 did not have a strong management and was behind schedule in submitting the cost report due to poor planning. Which of the following penalties are not possible
- A.
-70 points
- B.
-80 points
- C.
-90points
- D.
-5 points
- E.
-60 points
- F.
Both c&d
Correct Answer
F. Both c&dExplanation
The penalties for not submitting the cost report on time are -70 points, -80 points, -90 points, -5 points, and -60 points. The answer states that both penalties for -90 points and -5 points are not possible. This suggests that the team may have received penalties for being behind schedule, but not specifically for -90 points or -5 points.Rate this question:
-
- 16.
The load applicator used to test any panel or tube must be metallic and have a radius of 50 mm.
- A.
Metallic with 50mm diameter
- B.
Non metallic with 50mm diameter
- C.
Non metallic with 25mm diameter
- D.
Non metallic with 25mm radius
- E.
Metallic with 50mm radius
- F.
Metallic with 30mm diameter
Correct Answer
E. Metallic with 50mm radiusExplanation
The correct answer is metallic with 50mm radius. This is because the load applicator used to test any panel or tube must be metallic to ensure durability and strength. Additionally, the radius of the load applicator should be 50mm to provide a consistent and standardized measurement.Rate this question:
-
Back to top