Velocita Racing Rulebook Quiz

20 Questions | Total Attempts: 38

SettingsSettingsSettings
Please wait...
Velocita Racing Rulebook Quiz


Questions and Answers
  • 1. 
    Which of the following is not a positive locking mechanism?
    • A. 

      Jam nuts

    • B. 

      Tab washers

    • C. 

      K nuts

    • D. 

      Jet nuts

  • 2. 
    If the attachment of the drivers harness is not welded to a steel structure, then the attachments for shoulder and lap belts must support a load of ______ and the attachment points of the anti-submarine belts must support a load of _____. 
    • A. 

      16.5 kN, 13 kN

    • B. 

      13 kN, 6.5 kN

    • C. 

      6.5 kN, 13 kN

    • D. 

      16.5 kN, 6.5 kN

  • 3. 
    All aerodynamic devices forward of a vertical plane through the rearmost portion of the front face of the driver head restraint support, excluding any padding, set to its most ______ position, must be lower than _____ from the ground. 
    • A. 

      Rearward, 500mm

    • B. 

      Forward, 500mm

    • C. 

      Rearward, 250mm

    • D. 

      Forward, 250mm

  • 4. 
    Which of the following statement(s) is/are not true?
    • A. 

      Catch cans, mountings and hoses must be made of material that is permanently rated for temperatures of at least 100 degree celcius.

    • B. 

      Any vent for other systems containing liquid lubricant or coolant must have a catch-can with a minimum volume of 10% of the fluid being contained or 1000 ml, whichever is greater.

    • C. 

      Any catch can on a cooling system must vent through a hose with a minimum internal diameter of 2.5 mm down to the bottom levels of the chassis.

    • D. 

      All of the above

  • 5. 
    When seated normally and restrained by the driver’s restraint system, the helmet of a 95th percentile male and all of the team’s drivers must be a minimum of 50 mm away from the straight line drawn from the top of the main hoop to the upper end of the main hoop bracing if the bracing extends rearwards. 
    • A. 

      True

    • B. 

      False

  • 6. 
    The cockpit must provide a free internal cross section sufficient for the template to pass from the cockpit opening to a point __________ in an inoperative position.
    • A. 

      10 cm forwards of the face of the rearmost pedal

    • B. 

      10 cm rearwards of the face of the rearmost pedal

    • C. 

      10 cm rearwards of the face of the frontmost pedal

    • D. 

      10 cm forwards of the face of the frontmost pedal

  • 7. 
    If two parts of the primary structure are bolted together, _____________.
    • A. 

      Each attachment point between the two parts must be able to carry a load of 30 kN in one direction

    • B. 

      Any one attachment point between the two parts must be able to carry a load of 30 kN in any direction

    • C. 

      Each attachment point between the two parts must be able to carry a load of 30 kN in any direction

    • D. 

      Any one attachment point between the two parts must be able to carry a load of 30 kN in one direction

  • 8. 
    If the part material of 2 parts and an assembly is missed out of the BOM, how many points shall be deducted from the team's score in the cost and manufacturing event?
    • A. 

      5

    • B. 

      6

    • C. 

      7

    • D. 

      8

  • 9. 
    The main hoop braces must be attached to the main hoop ________ below the top-most surface of the main hoop. The included angle formed by the main hoop and the main hoop braces must be _______. 
    • A. 

      Higher than 160mm, <= 30°

    • B. 

      Lower than 160mm, <= 30°

    • C. 

      Higher than 160mm, >= 30°

    • D. 

      Lower than 160mm, >= 30°

  • 10. 
    Which of the following joint(s) between all components attaching the steering wheel to the steering rack is/are not allowed?
    • A. 

      Welded joint

    • B. 

      Bonded joint

    • C. 

      Bolted joint

    • D. 

      None of the above

  • 11. 
    Which of the following statement(s) is/are true regarding a CBOM?
    • A. 

      The cost calculations must include research, development and capital expenditures

    • B. 

      The costs of hand or power tools must be included.

    • C. 

      The estimations for machining rates, hourly rates, included overheads etc. must not be shown.

    • D. 

      None of the above

  • 12. 
    The upper member of the side impact structure must connect the main hoop and the front hoop and must be at _________ between the front and main hoop. 
    • A. 

      A height between 240 mm and 320 mm below the lowest inside chassis point

    • B. 

      A height between 240 mm and 320 mm above the highest inside chassis point

    • C. 

      A height between 220 mm and 340 mm above the lowest inside chassis point

    • D. 

      A height between 240 mm and 320 mm above the lowest inside chassis point

  • 13. 
    Which of the following statement(s) is/are true regarding the IA and AIP?
    • A. 

      The IA must be at least 100 mm high and 200 mm wide for a maximum distance of 200 mm forward of the front bulkhead.

    • B. 

      The AIP must extend past the outside edges of the front bulkhead.

    • C. 

      The IA may be attached to the AIP by a minimum of eight 8 mm metric grade 8.8 bolts.

    • D. 

      None of the above

  • 14. 
    If the lap belts and anti-submarine belts are attached less than 10 cm apart, these must support a total load of ______ .
    • A. 

      13 kN

    • B. 

      6.5 kN

    • C. 

      19.5 kN

    • D. 

      16.5 kN

  • 15. 
    All aerodynamic devices higher than 500 mm from the ground, must not extend ______ of the most ______ point of the _____ wheel/tire. 
    • A. 

      Outboard, outboard, rear

    • B. 

      Outboard, inboard, rear

    • C. 

      Inboard, outboard, front

    • D. 

      Inboard, inboard, front

  • 16. 
    Which of the following statement(s) is/are not true?
    • A. 

      Halon extinguishers and systems are allowed for the competition.

    • B. 

      The body of any camera or recording unit must be secured at a minimum of three points on different sides of the camera body. 

    • C. 

      Proban gloves do not qualify under the competition regulations of driver equipments.

    • D. 

      All of the above

  • 17. 
    BSE stands for
    • A. 

      Brake System Enhancer

    • B. 

      Bias System Enhancer

    • C. 

      Brake System Encoder

    • D. 

      Bias System Encoder

  • 18. 
    The correct sequence among the following is
    • A. 

      Restrictor > Compressor > Throttle Body > Air Cooler

    • B. 

      Restrictor > Throttle Body > Compressor > Air Cooler

    • C. 

      Compressor > Restrictor > Throttle Body > Air Cooler

    • D. 

      None of the above

  • 19. 
    A flexible fuel tank must be
    • A. 

      Flexibly mounted 

    • B. 

      Rigidly mounted 

    • C. 

      Either of 1 and 2

    • D. 

      Neither of 1 and 2

  • 20. 
    Which of the following statement(s) is/are not true?
    • A. 

      Safety wired bolts with Nyloc nuts are not allowed for mounting the brake calipers.

    • B. 

      Rod ends in single shear captured by a washer larger than the ball diameter are not allowed.

    • C. 

      The e/D ratio of suspension tabs must be greater than 1.5.

    • D. 

      All of the above

Back to Top Back to top