Spec Doc, Symbology, Gis Exam

73 Questions | Total Attempts: 15

SettingsSettingsSettings
Please wait...
Spec Doc, Symbology, Gis Exam


Questions and Answers
  • 1. 
    What does BSSP stand for and what joint type should be used?
    • A. 

      Black Screwed Steel Pipe, Screwed for Joint Type

    • B. 

      Black Stainless Steel Pipe, Null for Joint Type

    • C. 

      Black Screwed Steel Pipe, Null for Joint Type

    • D. 

      Black Stainless Steel Pipe, Welded for Joint Type

  • 2. 
    What does BSSP stand for and what joint type should be used?
    • A. 

      Black Screwed Steel Pipe, Screwed for Joint Type

    • B. 

      Black Stainless Steel Pipe, Null for Joint Type

    • C. 

      Black Screwed Steel Pipe, Null for Joint Type

    • D. 

      Black Stainless Steel Pipe, Welded for Joint Type

  • 3. 
    What does BWSP stand for and what joint type should be used?
    • A. 

      Black Wrapped Steel Pipe, joint type should be null

    • B. 

      Black Wrapped Steel Pipe, joint type should be welded

    • C. 

      Black Welded Steel Pipe, joint type should be welded

    • D. 

      Black Welded Steel Pipe, joint type should be null

  • 4. 
    What does LOA stand for?
    • A. 

      Letter of Authority

    • B. 

      Level of Activity

    • C. 

      Land Operating Area

    • D. 

      Local Operating Area

  • 5. 
    If Shortstopp Tee (SST) is shown on linen, what type of fitting should be captured?
    • A. 

      Controllable Fitting Shortstopp

    • B. 

      Controllable Fitting Shortstopp, Full Encirclement

    • C. 

      Controllable Fitting Shortstopp, Tee Full Encirclement

    • D. 

      Controllable Fitting Three Way Tee

  • 6. 
    If you come across this date 9-68 on linen, how would you capture it in GIS.
    • A. 

      9/1/1968

    • B. 

      1/9/1968

    • C. 

      1/1/1968

    • D. 

      1/1/1800

  • 7. 
    What date & WO info does stub-in-service get?
    • A. 

      In-Service Date & WO on service card for service

    • B. 

      In-Service Date & WO of gas main it is connected to

    • C. 

      Default date & WO

    • D. 

      In-Service Date & WO on linen for service

  • 8. 
    If GML shows 12.5' SN ROW MCCORMICK ST ON LINEN, how will this be captured in GIS?
    • A. 

      12' SN ROW MCCORMICK ST

    • B. 

      12.5' SN ROW MCCORMICK ST

    • C. 

      13' SN ROW MCCORMICK ST

    • D. 

      5' SN ROW MCCORMICK ST

  • 9. 
    If any line feature (gas mains, gas pipe casings, or service lines) that has relations needs to be split, then the editor does not have to re-relate any, such as Gas Pipe Casing, CP circuit, Gas Pressure System, and Line Section Number.
    • A. 

      True

    • B. 

      False

  • 10. 
    If gas main has been retired in GIS and GML for gas main is left active, what should be done?
    • A. 

      Abandoned gas main location should be captured for abandoned gas main

    • B. 

      Delete existing gas main location

    • C. 

      Nothing, it is not within the scope of the project to handle abandoned features

    • D. 

      Both A and B

  • 11. 
    What does PCF stand for?
    • A. 

      Pneumatic Connector Fitting

    • B. 

      Pressure Control Fitting

    • C. 

      Push-to-Connect Female Fitting

    • D. 

      Plastic Composite Fitting

  • 12. 
     How do non-controllable fittings and controllable fittings affect the gas main differently
  • 13. 
    What type of feature class in GIS does the symbols above represent?
    • A. 

      Non-Controllable Fitting

    • B. 

      Gas Valve

    • C. 

      Controllable Fitting

    • D. 

      Drip

  • 14. 
    How long (measured length) should offset for two pipes crossing on linen be?
    • A. 

      1'

    • B. 

      3'

    • C. 

      2'

    • D. 

      4'

  • 15. 
    For question above, will this length be subtracted from total measured length on adjacent main with matching size and subtype?
    • A. 

      Yes

    • B. 

      No

  • 16. 
    How long (measured length) should offset be for I-beam symbol on linen shown at intersection where no specific measurement is called out between I-Beam and Intersection?
    • A. 

      1'

    • B. 

      3'

    • C. 

      2'

    • D. 

      4'

  • 17. 
    For question above, will this length be subtracted from total measured length on adjacent main?
    • A. 

      Yes

    • B. 

      No

  • 18. 
    For the offset rule when two pipes cross on linen, if the larger main is the newer main, the larger main will always remain continuous.
    • A. 

      True

    • B. 

      False

  • 19. 
    When a box with text SS is shown at tee junction in linen then we should capture a Shortstopp Fitting.
    • A. 

      True

    • B. 

      False

  • 20. 
    When should we capture fittings on services?
    • A. 

      Never, we ignore all fittings shown on services

    • B. 

      Always capture fittings shown on services

    • C. 

      Size 2" or greater

    • D. 

      Size 1" or greater

  • 21. 
    Controllable Fittings always split the gas main.
    • A. 

      True

    • B. 

      False

  • 22. 
    In what circumstances is an offset for two pipes crossing not done in GIS?
    • A. 

      Cross fitting is shown at intersection

    • B. 

      Jumper is shown at intersection

    • C. 

      Controllable fitting is shown at intersection

    • D. 

      Both A and B

    • E. 

      All of the above

  • 23. 
    How long should the shape length be for a 1' gas main in GIS?
    • A. 

      1'

    • B. 

      2'

    • C. 

      10'

    • D. 

      4'

  • 24. 
    Per our current spec doc standards, what date is used for default when no date is given on the linen?
    • A. 

      1/1/1700

    • B. 

      1/1/1800

    • C. 

      1/1/1900

    • D. 

      1/1/1600

  • 25. 
    If Posi-Hold is shown on linen, what type of joint type is used?
    • A. 

      Null

    • B. 

      Welded

    • C. 

      Compression

    • D. 

      Screwed

Back to Top Back to top