Age CDC Volume 1

90 Questions

Settings
CDC Quizzes & Trivia

.


Questions and Answers
  • 1. 
    Risk management principles should be applied to 
    • A. 

      Only duty related activities to enhance the safety and wellbeing of yourself and others

    • B. 

      On and off duty activities to enhance the safety and well being of yourself and others

    • C. 

      Only duty related activities to protect yourself and other airmen from imminent harm

    • D. 

      On and off duty activities to protect yourself and other airmen from immenent harm

  • 2. 
    What situation does not warrant prompt reporting to your supervisor?
    • A. 

      Using personal protective equipment

    • B. 

      Unsafe working conditions

    • C. 

      Known pregnancies

    • D. 

      Personal injury

  • 3. 
    The effect of noise on your hearing depends on the 
    • A. 

      Frequency, deflection, and duration of exposure

    • B. 

      Frequency volume and duration of exposure

    • C. 

      Deflection volume and duration of exposure

    • D. 

      Deflection frequency and volume

  • 4. 
    The frame of an electrical motor should always be grounded to prevent 
    • A. 

      The energized windings from touching the frame

    • B. 

      Current from following the path of least resistance

    • C. 

      You from receiving an electrical shock if the energized motor windings touch the frame

    • D. 

      Current from flowing directly to ground if the energized motor windings touch the frame

  • 5. 
    Before removing a component from an air compressor, you must ensure 
    • A. 

      The air compressor is grounded

    • B. 

      The battery is disconnected

    • C. 

      The air strainer is in place

    • D. 

      All air pressure is drained

  • 6. 
    The primary cause of foreign object damage FOD is 
    • A. 

      Aircraft malfunctions

    • B. 

      Naturally occurring phenomena

    • C. 

      People failing to police their work areas

    • D. 

      Poorly maintained aerospace ground equipment AGE

  • 7. 
    How can people best prevent foreign object damage FOD?
    • A. 

      Learn the basic classes of FOD and recognize its causes

    • B. 

      Periodically participate in FOD walks on taxiways and runways

    • C. 

      Look for loose objects discarded on the flightline during maintenance activities.

    • D. 

      Look for loose objects (stone, paper, or trash) pick them up when discovered, and encourage others to do the same.

  • 8. 
    Which type of hammer should you use to avoid damaging driving materials
    • A. 

      Claw

    • B. 

      Sledge

    • C. 

      Soft face

    • D. 

      Ball peen

  • 9. 
    What is the proper way to grip a ball peen hammer?
    • A. 

      It depends on the object you are striking

    • B. 

      Close to the end; not near the head nor the middle

    • C. 

      Next to the head; not near the middle nor close to the end

    • D. 

      Close to the middle; not near the end nor close to the head

  • 10. 
    The size of screw driver is determined by the shank
    • A. 

      Temper

    • B. 

      Weight

    • C. 

      Length

    • D. 

      Width

  • 11. 
    Which type of screw driver is used in tight places when there isn't enough room to use a standard screwdriver?
    • A. 

      Cross point

    • B. 

      Flat blade

    • C. 

      Phillips

    • D. 

      Offset

  • 12. 
    Which pliers have a locking device to hold materials securley?
    • A. 

      Snap ring

    • B. 

      Vice grips

    • C. 

      Water pump

    • D. 

      Diagonal cutters

  • 13. 
    Diagonal cutting pliers are designed to cut 
    • A. 

      Bolts

    • B. 

      Rivets

    • C. 

      Hard steel

    • D. 

      Small wire

  • 14. 
    If you must push a wrench rather than pull it, how should you do it?
    • A. 

      Grasp the handle near the socket

    • B. 

      Grip the wrench tightly near the center

    • C. 

      Use the base of your hand and hold your hand open

    • D. 

      Use the base of your palm and clutch the wrench tightly

  • 15. 
    Pinning of a file results when 
    • A. 

      Inadequate pressure is applied to a new file

    • B. 

      Excessive pressure is applied to a new file

    • C. 

      The file gets caught or stuck in the metal

    • D. 

      Metal particles are clogged in it's teeth

  • 16. 
    Before operating the pneumatic impact wrench, you must
    • A. 

      Carefully inspect it and ennsure it is properly lubricated

    • B. 

      Ensure no flammable vapors that could ignite are present

    • C. 

      Tighten all parts of the tool and replace any worn brushes

    • D. 

      Blow out the air hose to remove any matter that has collected in it

  • 17. 
    A cracked wheel on a bench grinder is identified by
    • A. 

      Its inability to properly sharpen tools

    • B. 

      A ringing sound when tapped lightly with a plastic mallet

    • C. 

      It's inability to rempve excess metal or to smooth metal surfaces

    • D. 

      A dull thudding sound when tapped lightly with a rubber hammer

  • 18. 
    Which part of the torque wrench scale is normally not used?
    • A. 

      Lower 10 percent

    • B. 

      Lower 20 percent

    • C. 

      Upper 20 percent

    • D. 

      Uper 10 percent

  • 19. 
    What does the -4 identify in fitting part number MS20822-4D?
    • A. 

      Military specification

    • B. 

      Air Force/Navy

    • C. 

      Type of fitting

    • D. 

      Fitting size

  • 20. 
    Which types of fittings sare designed for pressure systems up to 3000 pounds per square inch (psi)? 
    • A. 

      Flared fittings

    • B. 

      Standard fittings

    • C. 

      Flareless fittings

    • D. 

      Precision type flared fittings

  • 21. 
    When installing a flexible hose, you must provide slack or bend in the hose to 
    • A. 

      Prevent twisting of the hose

    • B. 

      Compensate for change length

    • C. 

      Place a mechanical load on the hose

    • D. 

      Protect it from a hot pipe or manifold

  • 22. 
    Prior to restoring a piece of equipment to operation that has been in storage, what section within the operations and service instrucation technical order (TO) would you consult to find instructions to do so safely and properly?
    • A. 

      Section 2 special service tools

    • B. 

      Section 3 preparation for use, storage, or shipment

    • C. 

      Section 4 Operatign instructions

    • D. 

      Section 5 National stock number and reference number index

  • 23. 
    Which section of the illustrated parts breakdown IPB contains an explanation of the coding used in the IPB?
    • A. 

      Section 1 Introduction

    • B. 

      Section 2 Repair parts list

    • C. 

      Section 3 Reference designator index

    • D. 

      Section 4 National stock number and reference number index

  • 24. 
    You need to find the part number for an item prior to ordering it from supply. You've obtained the appropriate illustrated parts breakdown (IPB) manual for the end item. Which section of the IPB should you use to find the major assembly to which the desired item belongs?
    • A. 

      Table of contents

    • B. 

      Reference designator index

    • C. 

      Appropriate figure illustration

    • D. 

      National stock number and reference number index

  • 25. 
    Which time compliance technical order (TCTO) is issued to correct unsafe conditions that if not corrected, could result in serious or fatal injury to personnel?
    • A. 

      Safety

    • B. 

      Urgent action

    • C. 

      Routine action

    • D. 

      Immediate action

  • 26. 
    Which type of time compliance technical order (TCTO) is often accomplished by contractors, modification centers, or specific Air Force activities higher than organizational/intermediate-level maintenance due to the complexity involved?
    • A. 

      Abbreviated TCTO

    • B. 

      Inspection TCTO

    • C. 

      Record TCTO

    • D. 

      Interim TCTO

  • 27. 
    The main advantage of using abbreviated technical orders (TO) is they
    • A. 

      Cover safety in more detail

    • B. 

      Serve as aupplemental material

    • C. 

      Paraphrase and eliminate the need for basic TO's

    • D. 

      Organize and simplify instructions in condensed version

  • 28. 
    Which abbreviated technical order (TO) provides guidance for checking the general serviceability of a piece of equipment including applicable safety warnings, cautions, and notes?
    • A. 

      Lubrication charts

    • B. 

      Illustrated parts breakdown

    • C. 

      Service inspection workcards

    • D. 

      Periodic inspection workcards

  • 29. 
    An example of a technical order (TO) deficiency is 
    • A. 

      Improper sequencing of pages

    • B. 

      Insufficient information

    • C. 

      Typographica errors

    • D. 

      Misspelled words

  • 30. 
    Which form should you submit to correct a technical order (TO) deficiency?
    • A. 

      AF Form 1000 Idea application

    • B. 

      AF Form 601, Equipment Action Request

    • C. 

      AFTO Form 95 Significant Historical Data

    • D. 

      AFTO Form 22, Technical Manual (TM) Change Recommendation and Reply

  • 31. 
    What are the two general classes of Air Force Publications?
    • A. 

      Supplements and instructions

    • B. 

      Instructions and manuals

    • C. 

      Pamphlets and manuals

    • D. 

      Departmental and Field

  • 32. 
    Which type of standard publication is used by lower head quarters to implement, amplify, interpret, or clarify a higher level publication?
    • A. 

      Supplemental

    • B. 

      Visual aids

    • C. 

      Bulletins

    • D. 

      Manuals

  • 33. 
    Which Air Force Instruction (AFI) discusses the process of assigning publication numbers to broach topical areas?
    • A. 

      AFI 33-36 Forms and Management

    • B. 

      AFI 33-360 Pubications and forms management

    • C. 

      AFI 36-2604 Publication numbers

    • D. 

      AFI 36-2903 Personnel Listings

  • 34. 
    The first number of a standard air force publication number is referred to as the series and represents the 
    • A. 

      Broad area covered

    • B. 

      Specific area covered

    • C. 

      Title of the publication

    • D. 

      Specific military personnel affected

  • 35. 
    Where do you access stanndard air force publications?
    • A. 

      List of applicable publications (LOAP)

    • B. 

      Base level functional publication library

    • C. 

      The air force website www.e-pubishing.af.mil

    • D. 

      AFI 33-360 Publications and forms management

  • 36. 
    What is the primary focus of the entire maintenance process?
    • A. 

      Corrective rather than preventive

    • B. 

      Corrective rather than conducive

    • C. 

      Preventive rather than corrective

    • D. 

      Preventive rather than inductive

  • 37. 
    What impact is made on the maintenance organization by ensuring availability of adequate parts, equipment, and training?
    • A. 

      Increasing bottlenecks and minimizing repair cycle time

    • B. 

      Increasing bottlenecks and maximizing repair cycle time

    • C. 

      Eliminatinng bottle necks and minimizing repair cycle time

    • D. 

      Eliminating bottlenecks and maximizing repair cycle time

  • 38. 
    Organizational maintenance consists of 
    • A. 

      on equipment tasks normally performed using the resources of an operating command at an operating location

    • B. 

      On equipment tasks normally performed using the resources of a supporting commannd or intermediate repair facility

    • C. 

      Off equipment tasks normally performed using the resources of an operating command at an operating location or intermediate repair facility

    • D. 

      Off or on equipment tasks that require highly specilized skills, sophisticated shop equipment and/or special facilities of a supporting command

  • 39. 
    Which maintenance levels are considered together as field maintenance
    • A. 

      Centralized and depot

    • B. 

      Depot and provisional

    • C. 

      Provisional and centralized

    • D. 

      Organizational and intermediate

  • 40. 
    The main purpose of the inspection system is to 
    • A. 

      Get ahead on unscheduled maintenance

    • B. 

      Keep the mechanic working on minor problems

    • C. 

      Ensure equipment continues operating and looks good

    • D. 

      Locate problems and repair faulty equipment before total failure

  • 41. 
    What type of inspection consists of two phases (phase 1 and phase 2 )
    • A. 

      Service

    • B. 

      Special

    • C. 

      Periodic

    • D. 

      Acceptance

  • 42. 
    Which inspection may be either scheduled or unscheduled?
    • A. 

      Service

    • B. 

      Special

    • C. 

      Periodic

    • D. 

      Operator

  • 43. 
    Nuclear certified equipment (NCE) is any equipment used for 
    • A. 

      Air transport

    • B. 

      Manufacturing munitions used in war time

    • C. 

      Handling storage shipping or ground transport of non nuclear weapons

    • D. 

      Handling storage shipping or ground transportation of nuclear weapons

  • 44. 
    Who is responsible for making positive identification of all unit nuclear certified equipment (NCE)?
    • A. 

      Every squadron member

    • B. 

      NCE commandant

    • C. 

      Unit commander

    • D. 

      NCE monitor

  • 45. 
    Although decertification of nuclear certified equipment (NCE) can be recommended by any Air Force agency to another agency, which agency can formally decertify the equipment?
    • A. 

      AFSC/SEW

    • B. 

      AFSC/AMU

    • C. 

      AETC/TRR

    • D. 

      AMC/A3A4

  • 46. 
    When new nuclear certified equipment (NCE) items are added, they are cosidered serviceable
    • A. 

      Upon obtaining higher headquarter approval

    • B. 

      Once all technical order requirements are met

    • C. 

      Upon obtaining wing commander approval

    • D. 

      Once all items are accounted for

  • 47. 
    What is the purpose of the Dull Sword program?
    • A. 

      Identify possible trends to prevent incidents

    • B. 

      Certify Nuclear Certified Equipment (NCE)

    • C. 

      Approve modifications to NCE

    • D. 

      Update weapons status

  • 48. 
    Which symbol indicates a operational check is overdue
    • A. 

      Red X

    • B. 

      Red dash

    • C. 

      Red diagonal

    • D. 

      Circled red X

  • 49. 
    If you discover that a scheduled inspection goes overdue two inspection cycles, what maintenance symbol should you then enter on the forms?
    • A. 

      Circled red X

    • B. 

      Red diagonal

    • C. 

      Red dash

    • D. 

      Red X

  • 50. 
    Which inspection is recorded in Part 2 Non scheduled Inspection of the Air Force Technical Order (AFTO) Form 244 Industrial Support Equipment Record?
    • A. 

      Operator

    • B. 

      Periodic

    • C. 

      Service

    • D. 

      Special

  • 51. 
    Which section of the Air Force Technical Order (AFTO) Form 244, Industrial Support equipment Record, is used to record a forms review?
    • A. 

      Part 2 non scheduled inspection

    • B. 

      Part 3 Scheduled Inspection

    • C. 

      Part 4 Supervisory Review

    • D. 

      Part 5 maintenance Delayed Discrepancy

  • 52. 
    The Air Force Technical Order (AFTO) Form 350 serves as 
    • A. 

      An identification and status tag

    • B. 

      A status and accountability label

    • C. 

      A marking and accountability tag

    • D. 

      An identification and accountability tag

  • 53. 
    What is the condition of a component bearing a green equipment condition label?
    • A. 

      Unserviceable (Condemned)

    • B. 

      Unserviceable (Reparable)

    • C. 

      Serviceable

    • D. 

      Suspended

  • 54. 
    What is the condition of a component bearing a red equipement condition tag?
    • A. 

      Unserviceable (Condemned)

    • B. 

      Unserviceable (Reparable)

    • C. 

      Serviceable

    • D. 

      Suspended

  • 55. 
    What color is the equipment condition tag attached to an item being held as an exhibit?
    • A. 

      Green

    • B. 

      White

    • C. 

      Brown

    • D. 

      Yellow

  • 56. 
    What maintenance supply form is used to order commonly stocked supplies or turn in excess or unserviceable property?
    • A. 

      AF Form 2005, Issue/Turn in request

    • B. 

      DD Form 1348-6 Receipt Document

    • C. 

      AFTO Form 350 Reparable Item Processing Tag

    • D. 

      DD Form 1348 - 1A Issue Release Receipt Document

  • 57. 
    What maintenance supply form is primarily used as a receiving document, but can also be used to turn in equipment?
    • A. 

      AF Form 2005 Issue Turn in Request

    • B. 

      DD Form 1348 Receipt document

    • C. 

      AFTO 350 Reparable Item Processing Tag

    • D. 

      DD Form 1348 -1A Issue Release Receipt Document

  • 58. 
    When entering maintenance data documentation (MDD), what entry serves as a concise but accurate description of the problem
    • A. 

      How malfunction

    • B. 

      Corrective action

    • C. 

      Action Taken

    • D. 

      Discrepancy

  • 59. 
    Which maintenance data documentation (MDD) code identifies the system that was worked on?
    • A. 

      Units

    • B. 

      Work Unit Code

    • C. 

      Category of labor

    • D. 

      Type maintenance

  • 60. 
    Which is the best example of supply conservation?
    • A. 

      Ordering twice the amount of supplies to ensure enough are available if needed

    • B. 

      Replacing all hardware on equipment at each self inspection

    • C. 

      Ordering the minimum supplies necessary to do a job

    • D. 

      Not keeping commonly used supplies on hand

  • 61. 
    What is a major concept regarding "economical use" of supplies and equipment?
    • A. 

      Use them only for their intended purposes

    • B. 

      Always order the lease expensive item to do the job

    • C. 

      Protect items from hazards such as fire or corrosion

    • D. 

      Order only the minimum supplies necessary for the job

  • 62. 
    Distinguish between "excess" and "surplus" as they apply to air force supply discipline.
    • A. 

      Excess and surplus are the same

    • B. 

      Excess and surplus are the turn in of property

    • C. 

      Surplus is no longer needed at your base, and excess is property no longer needed by another military service or federal agency

    • D. 

      Surplys is property no longer needed by another military service or federal agency and excess property no longer needed at your base

  • 63. 
    What are you required to do with Air Force property you might find and believe it to be lost or misplaced?
    • A. 

      Leave it where you found it

    • B. 

      Place it back into the supply system

    • C. 

      Take the item to the organizational commander

    • D. 

      Take it to the security forces lost and found section

  • 64. 
    Equipment that does not require an Air Force Technical Order (AFTO) Form 375, Selected support equipment repair cost estimate have a one time repair limit less than 75% of the replacement cost if the value of the item is 
    • A. 

      Less than 2500

    • B. 

      Less than 25,000

    • C. 

      More than 2500

    • D. 

      More than 25,000

  • 65. 
    In accordance with the unitofm repair replacement program to whom is the air force technical order (AFTO) Form 375 submitted prior to sending a piece of equipment to depot for repair?
    • A. 

      Major Command (MAJCOM)

    • B. 

      Inventory manager

    • C. 

      Quality assurance

    • D. 

      Originating unit

  • 66. 
    After the depot has repaired an item to whom do they send copies of the Air Force Technical Order (AFTO) Form 375, Selected Support Equipment Repair Cost Estimate?
    • A. 

      Supervisor

    • B. 

      Safety office

    • C. 

      Quality assurance

    • D. 

      Major command (MAJCOM) inventory manager and the originator

  • 67. 
    Items for which accountability is dropped from all records when they are issued are considered
    • A. 

      Due in from maintenance (DIFM)

    • B. 

      Nonexpendable

    • C. 

      Expendable

    • D. 

      Excess

  • 68. 
    Items that retain their identity throughout the period of their use and may be turned in and reissued for use by others are considered
    • A. 

      Due in from maintenance (DIFM)

    • B. 

      Non expendable

    • C. 

      Expendable

    • D. 

      Excess

  • 69. 
    What is a joint responsibility of both supply and using activities that requires each to keep appropriate records of consumption data that minimize requisitioning more supplies than are actually required?
    • A. 

      Stock control

    • B. 

      Conservation

    • C. 

      Pecuniary liability

    • D. 

      Product improvement program

  • 70. 
    An expected usage level is established for all benck stock items except 
    • A. 

      Reparable items

    • B. 

      Single issue items

    • C. 

      Unit package items

    • D. 

      Special requisition items

  • 71. 
    When the bench stock quantity level falls below 50% for an item, you should 
    • A. 

      Post a due out list

    • B. 

      Place a red tag on the bin

    • C. 

      Notify supply that stock level is low

    • D. 

      Initial the initial supply stock listing

  • 72. 
    What kind of liability is defined by the responsibility of a person to make good any loss, destruction, or damage of government property caused by misuse or neglect?
    • A. 

      Command

    • B. 

      Individual

    • C. 

      Pecuniary

    • D. 

      Property

  • 73. 
    How can a person be relieved from property responsibiblity other than by pecuniary liability?
    • A. 

      Turn in only

    • B. 

      Transfer only

    • C. 

      Turn in or transfer

    • D. 

      Cash collection voucher or statement of charges

  • 74. 
    What must be done if SSgt Ortiz refuses to admit pecuniary liability for the loss of a $275 lown mower for which he has custodial responsibility?
    • A. 

      A report of survey must be prepared

    • B. 

      A statement of charges must be prepared

    • C. 

      Charges must be made on a military pay order

    • D. 

      The mower must be replaced by one of equivilent value

  • 75. 
    A report of survey must be prepared when the cost of a lost or damaged item is 
    • A. 

      Less than $250

    • B. 

      Less than $500

    • C. 

      More than $500

    • D. 

      Incapable of being determined

  • 76. 
    What is the purpose of the Product Quality Deficiency Reporting (PQDR) system?
    • A. 

      Remove part status from the maintenance data collection system

    • B. 

      Prevent manufacturer errors in workmanship, repair, and modification

    • C. 

      Identify material deficiencies throughout the major command (MAJCOM)

    • D. 

      Provide data to activities that are responsible for development, procurment, and other logistics management functions

  • 77. 
    After discovering a deficiency that would be considered a category 1 Product Quality Deficiency Report (PQDR), it must be submitted to the screening point within
    • A. 

      24 hours

    • B. 

      2 calendar days

    • C. 

      5 calendar days

    • D. 

      10 calendar days

  • 78. 
    After a deficiency has been discovered that would be considered a category 2 product quality deficienty report (PQDR), when must it be submitted to the screening point?
    • A. 

      24 hours

    • B. 

      2 Calendar days

    • C. 

      5 Calendar days

    • D. 

      10 Calendar days

  • 79. 
    Within the deficiency reporting system, who assigns a report control number and ensures proper marking and handling of exhibits?
    • A. 

      Originating point

    • B. 

      Screening point

    • C. 

      Action point

    • D. 

      Support point

  • 80. 
    Within the deficiency reporting system, who is responsible for the resolution of the deficiency?
    • A. 

      Originating point

    • B. 

      Screening point

    • C. 

      Action Point

    • D. 

      Support Point

  • 81. 
    What type of workshop or working group brings togther personnel who manage aerospace ground equipment (AGE) equipment at the Air Force level, the depot-level managers at Warner Robins Air Logistics Center (WR-ALC) and prsonnel who maintain the equipment at the organization/using activity level?
    • A. 

      Reliability and Maintainability Workshop (R&MW)

    • B. 

      Product Improvement Working Group (PIWG)

    • C. 

      Utilization and Training Workshop (U&TW)

    • D. 

      Product Steering Working Group (PSWG)

  • 82. 
    Who typically briefs new aerospace ground equipment (AGE) agenda items during the Product Improvement Working Group (PIWG)
    • A. 

      Lead command (Air Force Materiel Command (AFMC))

    • B. 

      Major command (MAJCOM) AGE functional manager

    • C. 

      Individuals who submitted the new agenda items

    • D. 

      Warner Robins Air Logistics Center (WR-ALC)

  • 83. 
    Preventive maintenance for corrosion control includes 
    • A. 

      Evaluating, marking, and painting

    • B. 

      Cleaning, inspecting, and painting

    • C. 

      Inspecting, marking, and coating

    • D. 

      Cleaning, inspecting, and coating

  • 84. 
    On which type of metal can you leave corrosion as long as the component in operational?
    • A. 

      Aluminum

    • B. 

      Copper

    • C. 

      Brass

    • D. 

      Steel

  • 85. 
    Responsibility for development and implemation of the mobility plan rests with the 
    • A. 

      Worker

    • B. 

      Supervisor

    • C. 

      Mobility officer

    • D. 

      Squadron mobility activity

  • 86. 
    After connecting a voltmeter across the starter terminals and clamping a current probe around the positive battery cable, what must be done prior to cranking the engine when performing a starting system check on aerospace ground equipment (AGE)?
    • A. 

      Estimate the temperature of the bettery

    • B. 

      Prevent the engine from starting

    • C. 

      Perform a battery cable test

    • D. 

      Disconnect the voltmeter

  • 87. 
    How should you approach a parked aircraft with your vehicle
    • A. 

      Only when a guide is posted

    • B. 

      Within 25 fet of an aircraft with engines running

    • C. 

      With the drivers side of the vehicle toward the aircraft

    • D. 

      With the drivers side of the vehicle away from the aircraft

  • 88. 
    Before bolting split rims together, seal the valve stem to the wheel with silicone sealant or equivalent in order to preven
    • A. 

      Water from entering into the wheels

    • B. 

      The rims from flying apart

    • C. 

      Severe corrosion

    • D. 

      Weather cracks

  • 89. 
    What must you do before inflating the inner tube fully on a split rim tire?
    • A. 

      Torque wheel lug bolts

    • B. 

      Check tires for foreign objects

    • C. 

      Ensure rims are vompletely bolted together and torqued

    • D. 

      Verify the silicone sealant around the valve stem area dries enough to form a skin

  • 90. 
    When preparing aerospace ground equipment for storage, what components should be cleaned with a solution of 1.5 to 2.0 pounds of sodium bicarbonate to one gallon of water?
    • A. 

      Belts and pulleys

    • B. 

      Battery terminals

    • C. 

      Battery case holder

    • D. 

      Battery cable clamps