Grade 11 - Module 2

20 Questions | Total Attempts: 133

SettingsSettingsSettings
Grade 11 - Module 2 - Quiz

Questions and Answers
  • 1. 
    The unit of current
    • A. 

      Ampere

    • B. 

      Volt

    • C. 

      Ohms

    • D. 

      Non of the above

  • 2. 
    The unit of  voltage
    • A. 

      Ampere

    • B. 

      Volt

    • C. 

      Ohms

    • D. 

      Non of the above

  • 3. 
    The voltage is
    • A. 

      Force to move electron

    • B. 

      Force to move resistance

    • C. 

      Force to move battery

    • D. 

      Non of the above

  • 4. 
    Current in an electric circuit
    • A. 

      Flow of battery

    • B. 

      Flow of electrons

    • C. 

      Flow of resistance

    • D. 

      All of the above

  • 5. 
    The picture show a 
    • A. 

      Series circuit

    • B. 

      Parallel circuit

    • C. 

      Series and parallel

    • D. 

      Non of the above

  • 6. 
    The picture shown here is a 
    • A. 

      Series circuit

    • B. 

      Parallel circuit

    • C. 

      Resistor circuit

    • D. 

      Non of the above

  • 7. 
    The meter show here is 
    • A. 

      Digital

    • B. 

      Analog

    • C. 

      Ohms

    • D. 

      All of the above

  • 8. 
    The meter shown hers is 
    • A. 

      Digital

    • B. 

      Analog

    • C. 

      Ohms

    • D. 

      Non of the above

  • 9. 
    The mete used here to read
    • A. 

      Current

    • B. 

      Voltage

    • C. 

      Ohms

    • D. 

      All of the above

  • 10. 
    The meter used here to find
    • A. 

      Current

    • B. 

      Voltage

    • C. 

      Resistance

    • D. 

      All of the above

  • 11. 
    The mistakes in the diagram are
    • A. 

      The ammeter is connected wrong

    • B. 

      The Voltmeter is connected wrong

    • C. 

      Only ammeter is connected wrong

    • D. 

      Both a and b

  • 12. 
    The picture shows
    • A. 

      Tester

    • B. 

      Continuity tester

    • C. 

      Ohmmeter

    • D. 

      Ammeter

  • 13. 
    The safe method of measurin resistance is
    • A. 

      Switch OFF power

    • B. 

      Remove ammeter from the circuit

    • C. 

      Keep the power supply always active

    • D. 

      Remove voltmeter

  • 14. 
    The condition for connecting Ohmmeter is
    • A. 

      No condition of connecting probes

    • B. 

      There are always condition in connecting probe

    • C. 

      The red probe should connect to left and black to right

    • D. 

      Only one probe is required

  • 15. 
    When resistors are connected in series
    • A. 

      Total resistance increases

    • B. 

      Total resistance decreses

    • C. 

      Remain the same

    • D. 

      Non of the above

  • 16. 
    In a parallel connected resistors
    • A. 

      The total resistance increases

    • B. 

      The total resistance is below the smallest value

    • C. 

      Total resistance decreases

    • D. 

      No change in total resistance

  • 17. 
    The continuity testing is for
    • A. 

      Finding open circuit

    • B. 

      Finding short circuit

    • C. 

      To find break in wire

    • D. 

      All of the above

  • 18. 
    The two methods of measuring continuity are
    • A. 

      Using tester and wire

    • B. 

      Using Ohmmeter and continuity teter

    • C. 

      Using Voltmeter and Battery

    • D. 

      All of the above

  • 19. 
    In a circuit , the only one current flows through 
    • A. 

      Parallel circuit

    • B. 

      Series circuit

    • C. 

      Lamp connected in Parallel

    • D. 

      Non of the above

  • 20. 
    If three resistors are connected in Parallel
    • A. 

      Only one current flows

    • B. 

      Two currents flows

    • C. 

      Three current flows

    • D. 

      Four current flows

Back to Top Back to top