Eng Tech 2 - 2nd Nine Weeks Review

20 Questions | By Celenacrews | Updated: Dec 10, 2014 | Attempts: 61

Questions

Settings

Create your own Quiz

Eng Tech 2 - 2nd Nine Weeks Review - Quiz

Questions and Answers

1.

What are the default states of a Case structure?
- A.
  
  0 and 1
- B.
  
  True and False
- C.
  
  Yes and No
- D.
  
  On and Off
- E.
  
  Open and Closed
2.

Which two windows make up the backbone of all LabVIEW code?
- A.
  
  Front panel and back pane
- B.
  
  Schematic editor and back diagram
- C.
  
  Schematic editor and block diagram
- D.
  
  Back panel and front diagram
- E.
  
  Front panel and block diagram
3.

While the NXT Brick is targeted, if the Deploy button is pressed, the code will:
- A.
  
  Compile and download onto the NXT Brick
- B.
  
  Compile and run on the computer while maintaining communication with the NXT Brick via USB or Bluetooth
- C.
  
  Compile and download onto the NXT Brick and then run immediately
- D.
  
  Compile on the computer and run
- E.
  
  Cause the robot to drive off the table
4.

If the Power terminal on the Motor On function block is set to 100, then:
- A.
  
  The motor spins 100 degrees
- B.
  
  The motor spins at maximum speed
- C.
  
  The motor spins at 100 rpm
- D.
  
  The motor spins at 100 cm/sec
- E.
  
  None of the above
5.

What does rpm mean?
- A.
  
  Radians per minute
- B.
  
  Revolutions per module
- C.
  
  Revolutions per minutes
- D.
  
  Radians per machine
- E.
  
  Revolutions power module
6.

What is a While Loop?
- A.
  
  A structure that runs while it is being worked on
- B.
  
  A structure that always runs while the robot is on
- C.
  
  A structure that runs everything inside while a condition is met
- D.
  
  A structure that runs while the code is running
- E.
  
  A function on the front panel
7.

Comparison functions output ______ values.
- A.
  
  Boolean
- B.
  
  Integer
- C.
  
  String
- D.
  
  Constant
- E.
  
  Numeric
8.

The ultrasonic sensor outputs _____ values.
- A.
  
  Boolean
- B.
  
  Integer
- C.
  
  String
- D.
  
  Constant
- E.
  
  Numeric
9.

What type of data does a Case structure expect to take in?
- A.
  
  Integer
- B.
  
  Double
- C.
  
  Boolean
- D.
  
  String
- E.
  
  Constant
10.

What function is used to log data from the light sensor?
- A.
  
  Log Blue Dataset
- B.
  
  Log Red Dataset
- C.
  
  Log Green Dataset
- D.
  
  Read Red Sensor
- E.
  
  Read Light Sensor
11.

What is the most important thing to read when using AutoCAD?
- A.
  
  Ribbon panel
- B.
  
  Command prompt
- C.
  
  Drawing area
- D.
  
  Status bar
12.

What does the escape key do in AutoCAD?
- A.
  
  Returns to your previous zoomed view
- B.
  
  Cancels out of the current command
- C.
  
  Starts a new command
- D.
  
  Restarts the previous command
- E.
  
  Opens a new file
13.

When drawing in AutoCAD, what layer does your new geometry land on?
- A.
  
  0
- B.
  
  A-Wall
- C.
  
  Object Layer
- D.
  
  The newest layer created
- E.
  
  The current layer
14.

In AutoCAD, where do you create and manage layers?
- A.
  
  Layer Settings Manager
- B.
  
  Layer Options Manager
- C.
  
  Layer Status Manager
- D.
  
  Layer Properties Manager
- E.
  
  Command Prompt
15.

In AutoCAD, which of the following is not a valid Object Snap?
- A.
  
  Quarter
- B.
  
  Perpendicular
- C.
  
  Nearest
- D.
  
  Endpoint
- E.
  
  Node
16.

In AutoCAD, what does Ortho mode do?
- A.
  
  Keeps the cursor at 5 degree increments
- B.
  
  It is a type of line
- C.
  
  Keeps the cursor moving either vertical or horizontal
- D.
  
  It is a workspace
- E.
  
  It turns on all available snaps
17.

Where would you find the settings for your dimensions in an AutoCAD drawing?
- A.
  
  Dimension Styles
- B.
  
  Dimension Options
- C.
  
  Dimension Types
- D.
  
  Dimension Units
- E.
  
  Dimension Characteristics
18.

Which is not a valid zoom command in AutoCAD?
- A.
  
  Window
- B.
  
  Realtime
- C.
  
  Down
- D.
  
  Extents
- E.
  
  Previous
- F.
  
  Dynamic
- G.
  
  Scale
19.

There are two methods for placing a Hatch in an AutoCAD drawing. One is selecting boundary objects and the other is:
- A.
  
  Remove boundary objects
- B.
  
  Pick points
- C.
  
  Island detection
- D.
  
  Draw hatch lines
- E.
  
  Identify boundary hatch
20.

Which of the following does the CAD in AutoCAD stand for?
- A.
  
  Coronary artery disease
- B.
  
  Computer-assisted drawing
- C.
  
  Computer-aided drawing
- D.
  
  Computer-aided design
- E.
  
  Computers and design