CCNA Questions Certification Test! Trivia Quiz

72 Questions

SettingsSettingsSettings
CCNA Questions Certification Test! Trivia Quiz

.


Questions and Answers
  • 1. 
    Which Cisco NX-OS command displays kernel uptime?
    • A. 

      Show module

    • B. 

      Show version

    • C. 

      Show license

    • D. 

      Show boot

    • E. 

      Show interface

  • 2. 
    What is the name of this Cisco Nexus 3000 Series Switch?
    • A. 

      Cisco Nexus 3132Q

    • B. 

      Cisco Nexus 3172PQ

    • C. 

      Cisco Nexus 3524

    • D. 

      Cisco Nexus 3016

  • 3. 
    Which two statements about PCIe are true?
    • A. 

      The PCIe link is built around dedicated unidirectional couples of serial, point-to-point connections known as lanes.

    • B. 

      You can install a PCI Express x8 adapter into an x4 slot.

    • C. 

      The PCIe standard is a bus-based system in which all the devices share the same bidirectional, 32-bit or 64-bit, parallel signal path.

    • D. 

      The PCIe 1.0 standard doubles the transfer rate compared to PCIe 2.0.

    • E. 

      A link that is composed of four lanes is called an x4 link.

  • 4. 
    Which important feature on the front end is provided to the clients by multiple servers that access the same storage devices across the SAN?
    • A. 

      Recovery

    • B. 

      Redundancy

    • C. 

      Resiliency

    • D. 

      Security

    • E. 

      Storage

  • 5. 
    Which processor option is supported in the Cisco UCS C420 M3 Server?
    • A. 

      Up to two Intel Xeon E5-4600 series multicore processors

    • B. 

      Up to two Intel Xeon E7-4800 series multicore processors

    • C. 

      Up to four Intel Xeon E5-4600 series multicore processors

    • D. 

      Two or four Intel Xeon E7-8800 series multicore processors

  • 6. 
    What is the correct path to verify the Overall Status of Chassis 1 | Server 3?
    • A. 

      Equipment Tab > Chassis > Chassis 1 > Servers > Server 3 Status tab

    • B. 

      Equipment Tab > Chassis > Chassis 1 > Servers > Server 3 General tab

    • C. 

      Equipment Tab > Chassis > Chassis 1 > Servers > Server 3 FSM tab

    • D. 

      Servers Tab > Chassis > Server 3 General tab

    • E. 

      Status Tab > Chassis > Chassis 1 > Servers > Server 3

    • F. 

      Admin Tab > Chassis > Chassis 1 > Servers > Server 3 General tab

  • 7. 
    Which supervisor module is supported by a Cisco Nexus 7700 Series Switch?
    • A. 

      First-generation supervisor module

    • B. 

      Second-generation supervisor module (Sup2)

    • C. 

      Second-generation supervisor enhanced module (Sup2E)

    • D. 

      Third-generation supervisor enhanced module (Sup3E)

  • 8. 
    Which five things should the administrator verify after performing maintenance or replacing a blade server?
    • A. 

      Blade server status

    • B. 

      Hard drive status

    • C. 

      Host OS boot status

    • D. 

      CPU status

    • E. 

      Mezzanine card status

    • F. 

      Memory DIMM status

    • G. 

      Fan and power status

  • 9. 
    To do a password recovery on a Cisco NX-OS Switch, which option shows the correct syntax to display the bootflash contents at the switch(boot)#?
    • A. 

      Display bootflash:

    • B. 

      Show bootflash:

    • C. 

      Dir bootflash:

    • D. 

      Find bootflash:

  • 10. 
    Which method is a TCP/IP-based protocol for establishing and managing connections between IP-based storage devices, hosts, and clients?
    • A. 

      FCIP

    • B. 

      IFCP

    • C. 

      ISCSI

    • D. 

      FCoE

  • 11. 
    Which command can be used to exit to EXEC mode from this current mode? switch(config-if) #
    • A. 

      Ctrl-C

    • B. 

      Ctrl-L

    • C. 

      Quit

    • D. 

      Exit

    • E. 

      End

  • 12. 
    Which three statements about FCoE are true?
    • A. 

      Allows Fibre Channel and Ethernet networks to share a single, integrated infrastructure.

    • B. 

      Encapsulates Fibre Channel frames into Ethernet frames, which allows them to run alongside traditional IP traffic.

    • C. 

      Increases capital costs due to the difficulty to manage.

    • D. 

      Consolidates I/O traffic in the data center.

  • 13. 
    Which three options are the minimum browser requirements to log into the Cisco CIMC GUI?
    • A. 

      Java 1.6 or higher

    • B. 

      HTTP and HTTPS enabled

    • C. 

      Adobe Flash Player 10 or higher

    • D. 

      Internet Explorer version 10

    • E. 

      Firefox 26.0

    • F. 

      Adobe Shockwave Player 11 or higher

  • 14. 
    Up to what speed can Category 5e UTP cable transmit data?
    • A. 

      10 Mb/s

    • B. 

      100 Mb/s

    • C. 

      1000 Mb/s

    • D. 

      10000 Mb/s

  • 15. 
    What is the name of this rack-mount server?
    • A. 

      Cisco UCS C220 Rack-Mount Server

    • B. 

      Cisco UCS C240 Rack-Mount Server

    • C. 

      Cisco UCS C420 Rack-Mount Server

    • D. 

      Cisco UCS C460 Rack-Mount Server

  • 16. 
    Which two major components does a Cisco Nexus 1000V Series Switch have?
    • A. 

      Virtual Fiber Channel Module

    • B. 

      Virtual Ethernet Module

    • C. 

      Virtual Supervisor Module

    • D. 

      Virtual Memory Controller Module

    • E. 

      Virtual Network Module

  • 17. 
    Which command-line interface mode is best described by this prompt? UCS-switch-A (nxos)#
    • A. 

      Maintenance mode

    • B. 

      EXEC mode

    • C. 

      Local management mode

    • D. 

      Global configuration mode

    • E. 

      Cisco IOS mode

  • 18. 
    Which three tools are necessary to console into a Cisco UCS C-Series Rack-Mount Server?
    • A. 

      Cisco DB-9-to-RJ-45 console cable

    • B. 

      Laptop

    • C. 

      Monitor

    • D. 

      Keyboard

    • E. 

      KVM dongle

    • F. 

      USB serial adapter

  • 19. 
    Which three components are hot-swappable in a Cisco UCS Blade Server and Chassis?
    • A. 

      Fabric Extender

    • B. 

      Power supply

    • C. 

      Heat sink

    • D. 

      SAS Hard Drive

    • E. 

      2x8GB Kit DIMMs

    • F. 

      Mezzanine card

  • 20. 
    The Ethernet specification details several different fiber optic media types. What is the wire transmission speed for 100BASE-FX Ethernet?
    • A. 

      10 Mb/s

    • B. 

      100 Mb/s

    • C. 

      1000 Mb/s

    • D. 

      10000 Mb/s

  • 21. 
    What does the system status LED look like when an over temperature or major alarm occurs on the Cisco UCS 6120XP Fabric Interconnect?
    • A. 

      Amber

    • B. 

      Red

    • C. 

      Blinking amber

    • D. 

      Blinking red

  • 22. 
    What is the maximum number of supervisor modules that the Cisco MDS 9710 Switch supports?
    • A. 

      1

    • B. 

      2

    • C. 

      4

    • D. 

      6

    • E. 

      8

  • 23. 
    Which type of optics module is supported by a 6-port 40 GE Cisco Nexus 7000 M2 Series I/O module?
    • A. 

      CPAK

    • B. 

      QSFP+

    • C. 

      SFP/SFP+

    • D. 

      CFP

  • 24. 
    After installation or replacement of a Cisco UCS C-Series Rack-Mount Server, the host does not boot. Which four options should be verified?
    • A. 

      Verify the power source to the equipment.

    • B. 

      Check for loose HDD cables.

    • C. 

      Reseat the DIMMs, CPU, and PCI cards.

    • D. 

      Verify that power supplies are receiving power.

    • E. 

      Reseat the mezzanine card connector.

    • F. 

      Check the CPU sockets for bent pins.

    • G. 

      Check the Cisco IMC for fan faults.

  • 25. 
    Which three firmware components does the Host Upgrade Utility upgrade?
    • A. 

      Fabric Interconnect firmware

    • B. 

      LAN on Motherboard

    • C. 

      Cisco UCS Manager

    • D. 

      CIMC

    • E. 

      System BIOS

  • 26. 
    Which two statements about the Ethernet media are true?
    • A. 

      A twisted-pair cable system has each pair of wires twisted together to reduce electromagnetic interference.

    • B. 

      Compared to multimode fiber, the single-mode fiber is designed for shorter distances with higher cost.

    • C. 

      40 Gigabit Ethernet twinax cables deploy Enhanced Quad Small Form Factor Pluggable (QSFP+) connectors.

    • D. 

      The twinax cables can be found in either a shielded twisted-pair or an unshielded twisted-pair variation

  • 27. 
    Where is the best place to find the B200 BIOS version used in a specific Cisco UCS Manager version?
    • A. 

      A - Installed Firmware

    • B. 

      B - Packages

    • C. 

      C - Images

    • D. 

      D - Capability Catalog

    • E. 

      E - Management Extension

    • F. 

      E - Management Extension

  • 28. 
    Which two Cisco Nexus switches provide the foundation of the Cisco Application Centric Infrastructure?
    • A. 

      Cisco Nexus 7718 switch

    • B. 

      Cisco Nexus 9508 switch

    • C. 

      Cisco Nexus 7710 switch

    • D. 

      Cisco Nexus 93128TX switch

    • E. 

      Cisco Nexus 6004 switch

  • 29. 
    Which type of connection across the network does a SAN allow for multiple servers to access an unlimited amount of storage devices?
    • A. 

      Any-to-many

    • B. 

      Many-to-any

    • C. 

      Any-to-any

    • D. 

      Any-to-one

    • E. 

      One-to-any

    • F. 

      One-to-one

  • 30. 
    Where is the best place to see the power supply status of the blade server enclosure?
    • A. 

      A - Chassis 1

    • B. 

      B - Chassis 1 - PSUs

    • C. 

      C - Chassis1 - Servers

    • D. 

      D - Rack-Mounts - Servers

    • E. 

      E - Fabric Interconnects A - PSUs

  • 31. 
    On the Sensors page from the CIMC view, which four tabs are displayed to view further information?
    • A. 

      Power Supply

    • B. 

      Fan

    • C. 

      Memory

    • D. 

      CPU

    • E. 

      LEDs

    • F. 

      Temperature

  • 32. 
    Which two statements about the Cisco Nexus 5596UP switch are true?
    • A. 

      Its power supplies and fan trays are hot-swappable.

    • B. 

      It supports unified ports.

    • C. 

      It is offered in a one-rack-unit form factor.

    • D. 

      It has one expansion slot.

    • E. 

      It supports up to 96 10G BASE-T ports.

  • 33. 
    Which option should you select to get the output of the show tech-support detail command for the Cisco UCS B-Series blade?
    • A. 

      A - ucsm

    • B. 

      B - chassis

    • C. 

      C - fabric-extender

    • D. 

      D - rack-server

  • 34. 
    Which three steps do you perform to troubleshoot when a rack server powers on with no video? 
    • A. 

      Check that the front I/O dongle is properly seated.

    • B. 

      Check the front I/O cable connection to the motherboard.

    • C. 

      Check for memory subsystem failure.

    • D. 

      Verify the power source to equipment.

    • E. 

      Reseat the DIMMs, CPU, and PCI cards.

  • 35. 
    Which Cisco MDS model supports the most Fibre Channel ports per chassis?
    • A. 

      MDS 9513

    • B. 

      MDS 9509

    • C. 

      MDS 9506

    • D. 

      MDS 9250i

  • 36. 
    Which command syntax is correct to reset the admin password when the switch is in the kickstart prompt "switch(boot) #"?
    • A. 

      Exec -> admin-password <password>

    • B. 

      Connect local-mgmt -> admin-password <password>

    • C. 

      Configure terminal -> admin-password <password>

    • D. 

      Connect nxos -> admin-password <password>

    • E. 

      Admin-password <password>

  • 37. 
    Which three troubleshooting procedures do you perform when there is no power to a Cisco UCS B250 M2 Blade Server? 
    • A. 

      Decommission and acknowledge the blade.

    • B. 

      Check the back of the blade to ensure that there is no damage to the connection that goes into chassis.

    • C. 

      Reseat the memory DIMMs.

    • D. 

      Check the CPU sockets for bent pins.

    • E. 

      Reseat the blade in the same slot in the chassis.

    • F. 

      Move the blade to another slot in the chassis.

  • 38. 
    Which device provides analysis of Fibre Channel traffic without any network disruption?
    • A. 

      Cisco MDS 9000 Data Analyzer Adapter

    • B. 

      Cisco MDS 9000 Port Analyzer Adapter

    • C. 

      Cisco MDS 9000 Channel Analyzer Device

    • D. 

      Cisco MDS 9000 Channel Analyzer Adapter

  • 39. 
    Which two remote file system methods are used in the training material to transfer firmware to the Fabric Interconnect?
    • A. 

      FTPS

    • B. 

      FTP

    • C. 

      TFTP

    • D. 

      RSH

  • 40. 
    Which three options are features of the Cisco UCS 6248UP Fabric Interconnect front panel?
    • A. 

      Console port

    • B. 

      FCoE port

    • C. 

      10 Gb/s port

    • D. 

      Fan module

    • E. 

      USB port

  • 41. 
    Which call-out accurately shows the current running version of the Cisco UCS Manager management software?
    • A. 

      A - UCS Manager running version 1.4(1m)

    • B. 

      B - IO Module 1 running version 1.4(1m)

    • C. 

      C - Interface Card 1 running version 1.4(1m)

    • D. 

      D - Kernel running version 4.2(1)N(1.4m)

  • 42. 
    Which item does A represent?
    • A. 

      Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers

    • B. 

      Virtual Interface Card for Cisco UCS B420 M3 Blade Servers

    • C. 

      MLOM for Cisco UCS B420 M3 Blade Servers

    • D. 

      Virtual Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers

    • E. 

      SuperCap module for Cisco UCS B420 M3 Blade Servers

  • 43. 
    Which Cisco MDS chassis supports the 48-Port 16-Gbps Fibre Channel Switching Module?
    • A. 

      MDS 9509

    • B. 

      MDS 9513

    • C. 

      MDS 9710

    • D. 

      MDS 9506

  • 44. 
    Which two statements about DIMM replacement in Cisco UCS Servers are true? (Choose two.)
    • A. 

      In blade servers, DIMMs can be installed in either 1, 2, 4, or 8 DIMMs per channel.

    • B. 

      Rack-mount and blade servers have memory fault LEDs that indicate which DIMM requires attention.

    • C. 

      In servers that require pairs of DIMMs, the pairs must be identical (manufacturer, size, part #, and so on).

    • D. 

      If the memory in a server is not fully populated, you can install DIMMs in any open slot.

  • 45. 
    When a host firmware package policy is created, what must it be associated with to upgrade the BIOS?
    • A. 

      Blade or blade pool

    • B. 

      Service profile

    • C. 

      Boot policy

    • D. 

      Service template

  • 46. 
    If the Overall Status for a Cisco UCS B-Series Blade Server indicates a failure in the Cisco UCS Manager, such as discovery-failed, which statement is true?
    • A. 

      The server shuts down.

    • B. 

      The server automatically reboots reboot in 3 minutes.

    • C. 

      The endpoints on that server cannot be upgraded.

    • D. 

      The server is online, but the administrator cannot assign a service profile to that blade.

  • 47. 
    Where is the best place to see whether the system is ready for a Fabric Interconnect failover?
    • A. 

      A - Overall Status operable

    • B. 

      B - L1 Connection

    • C. 

      C - Part Details

    • D. 

      D - Access

    • E. 

      E - High Availability Details

  • 48. 
    On which three devices can the Host Upgrade Utility be performed? (Choose three.)
    • A. 

      C420

    • B. 

      C230

    • C. 

      B230

    • D. 

      B210

    • E. 

      C210

    • F. 

      B460

    • G. 

      C240

  • 49. 
    Which item does F represent?
    • A. 

      HDD 1

    • B. 

      TFP Module

    • C. 

      SuperCap Module

    • D. 

      CPU 2

    • E. 

      CMOS Battery

  • 50. 
    Which statement correctly identifies the front panel LEDs on the Cisco UCS C220 Server?
    • A. 

      A is power button and power status LED; B is identification button and LED; C is system status LED; D is network link activity LED.

    • B. 

      A is network link activity LED; B is system status LED; C is power button and power status LED; D is identification button and LED.

    • C. 

      A is system status LED; B is network link activity LED; C is power button and power status LED; D is identification button and LED.

    • D. 

      A is network link activity LED; B is system status LED; C is identification button and LED; D is power button and power status LED.

  • 51. 
    How do you find the serial number of a Cisco UCS 5108 Blade Server chassis?
    • A. 

      Use the Cisco UCS Admin.

    • B. 

      Use the Cisco UCS Application.

    • C. 

      Use the Cisco UCS Assistant.

    • D. 

      Use the Cisco UCS Manager.

  • 52. 
    Which action should the administrator take before physically removing a blade server for maintenance or replacement?
    • A. 

      Force the server to shut down.

    • B. 

      Disassociate the service profile.

    • C. 

      Decommission the server.

    • D. 

      Perform a graceful shutdown of the server.

  • 53. 
    Which cable is used to access the command-line interface of a Cisco UCS 6120XP Fabric Interconnects?
    • A. 

      KVM cable

    • B. 

      Console cable

    • C. 

      Ethernet cable

    • D. 

      SFP+ Ethernet transceiver cable

  • 54. 
    Which three statements about powering down a Cisco UCS C-Series Rack-Mount Server to perform maintenance or replacement are true? (Choose three.)
    • A. 

      Standby power mode: Power is supplied only to the service processor and the cooling fans, and it is safe to power off the server from this mode.

    • B. 

      Power status LED. Green indicates that the server is in main power mode and can be safely powered off.

    • C. 

      Graceful shutdown: Press and release the power button. The operating system performs a graceful shutdown, and the server goes to standby mode, which is indicated by an amber power status LED.

    • D. 

      Disconnect the power cords from the power supplies in your server to completely power off the server.

    • E. 

      Only an emergency shutdown can be performed using the power button on the server front panel.

    • F. 

      The Cisco UCS C-Series Rack-Mount Server has only one power mode.

  • 55. 
    Which method does FCIP use to enable connectivity of geographically distributed Fibre Channel SANs over IP?
    • A. 

      Routing

    • B. 

      Tunneling

    • C. 

      Handshaking

    • D. 

      Transporting

  • 56. 
    What is the wire transmission speed for 100GBASE-ER4 Ethernet?
    • A. 

      100 Mb/s

    • B. 

      1 Gb/s

    • C. 

      10 Gb/s

    • D. 

      100 Gb/s

  • 57. 
    Which two commands allow you to view the state of high availability between the two clustered Fabric Interconnects? (Choose two.)
    • A. 

      Show cluster state extended

    • B. 

      Show cluster extended-state

    • C. 

      Show cluster HA status

    • D. 

      Show cluster state

  • 58. 
    How many 10GBASE-T port licenses are preinstalled on a Cisco Nexus 3064-32T?
    • A. 

      16

    • B. 

      32

    • C. 

      48

    • D. 

      64

  • 59. 
    Where is the best place to see bootflash free space?
    • A. 

      A - Available Memory

    • B. 

      B - Total Memory

    • C. 

      C - Local Storage Information

    • D. 

      D - High Availability Details

  • 60. 
    Which Cisco Nexus 5000 Series model supports 1/10G BASE-T ports?
    • A. 

      Cisco Nexus 5548P

    • B. 

      Cisco Nexus 5548UP

    • C. 

      Cisco Nexus 5596UP

    • D. 

      Cisco Nexus 5596T

  • 61. 
    Which two commands display the version of Cisco NX-OS code that the device is currently running on? (Choose two.)
    • A. 

      Show version

    • B. 

      Show module

    • C. 

      Show interface

    • D. 

      Show boot

    • E. 

      Show license

  • 62. 
    Up to what speed can Category 5 UTP cable transmit data?
    • A. 

      10 Mb/s

    • B. 

      100 Mb/s

    • C. 

      1000 Mb/s

    • D. 

      10000 Mb/s

  • 63. 
    Which command saves the active configuration to NVRAM?
    • A. 

      Copy startup-config running-config

    • B. 

      Copy active-config backup-config

    • C. 

      Copy running-config startup-config

    • D. 

      Copy backup-config active-config

  • 64. 
    When the Cisco UCS Manager is used to verify the B- or C-Series device, which two types of Overall Status are acceptable and do not indicate a failure? (Choose two.)
    • A. 

      Online

    • B. 

      OK

    • C. 

      Unassociated

    • D. 

      Active

  • 65. 
    Which tool does a network administrator not need when installing hardware?
    • A. 

      Cable tester

    • B. 

      Wrench set

    • C. 

      Cable wraps

    • D. 

      Needle-nose pliers

    • E. 

      PCMCIA memory

    • F. 

      Soldering iron with grounded tip

  • 66. 
    This image shows a CPU Pick-and-Place tool and a CPU Socket Protective Cap Removal tool. Which types of Cisco UCS servers and Intel Xeon processors do these tools support?
    • A. 

      Cisco UCS B22 Blade Server, C22 Rack Server, and C24 Rack Sever with Intel Xeon E5-2400 Series processors

    • B. 

      Cisco UCS B22 Blade Server, C22 Rack Server, and C24 Rack Sever with Intel Xeon E5-2600 Series processors

    • C. 

      Cisco UCS B200 M3 Blade Server, B420 M3 Blade Server, C220 Rack Server, C240 Rack Sever, and C420 Rack Sever with Intel Xeon E5-2400 Series processors

    • D. 

      Cisco UCS B200 M3 Blade Server, B420 M3 Blade Server, C220 Rack Server, C240 Rack Sever, and C420 Rack Sever with Intel Xeon E5-2600 Series processors

  • 67. 
    What is the maximum distance that the 40GBASE-LR4 Ethernet standard can span?
    • A. 

      550 m

    • B. 

      10 km

    • C. 

      40 km

    • D. 

      80 km

  • 68. 
    Which type of optics module is supported by a 12-port 100 GE Cisco Nexus 7700 F3 Series I/O module?
    • A. 

      CPAK

    • B. 

      QSFP+

    • C. 

      SFP/SFP+

    • D. 

      CFP

  • 69. 
    Which fiber optic cable type is used most often with a Subscriber connector?
    • A. 

      Dual-mode

    • B. 

      Single-mode

    • C. 

      Straight-mode

    • D. 

      Multi-mode

    • E. 

      Subscriber-mode

  • 70. 
    Where do you find the model number of a Cisco MDS 9200 Series chassis?
    • A. 

      On the top front of the chassis next to the serial number

    • B. 

      On the bottom front of the chassis next to the Cisco logo

    • C. 

      On the top front of the chassis next to the Cisco logo

    • D. 

      On the bottom front of the chassis next to the serial number