Bay Path Jointer

15 Questions | Total Attempts: 89

SettingsSettingsSettings
Please wait...
Instrument Quizzes & Trivia

Safety Instructions


Questions and Answers
  • 1. 
    Be careful that you do not run any material that might have ___________ in it over the jointer.
    • A. 

      Reverse grain

    • B. 

      Open pitch pockets

    • C. 

      Long glue joints

    • D. 

      Nails, screws, or loose knots

  • 2. 
    Always see that the jointer is set to the right depth of cut, about ___________ inch, before you turn on the power.
    • A. 

      1/8

    • B. 

      1/16

    • C. 

      3/16

    • D. 

      1/32

  • 3. 
    In edge jointing a board, do not machine material that is less than ___________ inch(es) square.
    • A. 

      1/2

    • B. 

      1

    • C. 

      2

    • D. 

      3/4

  • 4. 
    You must not use the jointer for face work which is less than___________ inch(es) thick.
    • A. 

      1/4

    • B. 

      1/2

    • C. 

      1

    • D. 

      2

  • 5. 
    You must not use the jointer for wood less than ___________ inches long.
    • A. 

      6

    • B. 

      12

    • C. 

      16

    • D. 

      24

  • 6. 
    You must use ___________ when jointing pieces less than 2 inches square.
    • A. 

      Finger pressure

    • B. 

      Even pressure

    • C. 

      Metal tool

    • D. 

      Push stick

  • 7. 
    You must always use a safety shoe or push block when jointing the ___________ of a piece of material.
    • A. 

      Left edge

    • B. 

      Left side

    • C. 

      Face side

    • D. 

      Top side

  • 8. 
    Do not use the jointer for cuts deeper than ___________ inch.
    • A. 

      1/32

    • B. 

      1/16

    • C. 

      1/8

    • D. 

      1/4

  • 9. 
    You should ___________ change the adjustment of the rear or out feed table.
    • A. 

      Always

    • B. 

      Never

    • C. 

      Sometimes

    • D. 

      Accurately

  • 10. 
    Push stop over the jointer with a ___________ motion (about 15ft/minute).
    • A. 

      Very quick

    • B. 

      Slow

    • C. 

      Steady

    • D. 

      Both b and c

  • 11. 
    Stand ___________ the jointer, not behind or in line with your material.
    • A. 

      In the back, behind

    • B. 

      Near the front of

    • C. 

      On the left, beside

    • D. 

      At the rear of

  • 12. 
    Shift your hands so they never pass over the knife head ___________.
    • A. 

      At the beginning of the cut

    • B. 

      On deep cuts

    • C. 

      At any time

    • D. 

      Until the end of the cut

  • 13. 
    When you cut ___________ on the jointer, you must clamp on a stop block to the fence or table to support the end of the board and prevent a kickback.
    • A. 

      Boards

    • B. 

      Deeply

    • C. 

      Edges

    • D. 

      Tapers

  • 14. 
    Jointer should never be used for jointing ___________.
    • A. 

      End grain

    • B. 

      Side grain

    • C. 

      Face surface

    • D. 

      Straight grain

  • 15. 
    Any operation which requires a special set-up must be approved by the instructor ___________ of the operation.
    • A. 

      After the start

    • B. 

      Prior to the start

    • C. 

      During the process

    • D. 

      At no time during the process