Gtc Practice Test

45 Questions

Settings
Practice Test Quizzes & Trivia

Questions and Answers
  • 1. 
    What is the minimum amount of fuel required to operate the gtc?
    • A. 

      5000 in one main tank

    • B. 

      1000 in one main tank

    • C. 

      2000 in one main tank

    • D. 

      3000 in one main tank

  • 2. 
    How many personnel are required to run operate the gtc?
    • A. 

      4

    • B. 

      1

    • C. 

      2

    • D. 

      3

  • 3. 
    Howmany qurats of  oil are required in the gtc oil tank?
    • A. 

      2

    • B. 

      3

    • C. 

      1

    • D. 

      4

  • 4. 
    How is a fire warning determined?
    • A. 

      Flashing lights in both the gtc t handle and master waring light

    • B. 

      Steady lights in both the gtc t handle and master warning light

    • C. 

      Steady light in the gtc fire fire handle

    • D. 

      Flashing light in the master warning light

  • 5. 
    Gtc fire detection system runs off of what bus
    • A. 

      Isolated dc

    • B. 

      Essential dc

    • C. 

      Battery

    • D. 

      Main dc

  • 6. 
    What is the minimum voltage on the dc voltimeter required to operate the gtc?
    • A. 

      25

    • B. 

      19

    • C. 

      21

    • D. 

      12

  • 7. 
    Gtc contril c/b runs off of what bus
    • A. 

      Isolated dc

    • B. 

      Essential dc

    • C. 

      Battery

    • D. 

      Main dc

  • 8. 
    How many minutes must you wait after turning the gtc off before starting the gtc again
    • A. 

      3

    • B. 

      2

    • C. 

      1

    • D. 

      4

  • 9. 
    The on speed light shou;d come on after ____ seconds after the start light comes on 
    • A. 

      15

    • B. 

      30

    • C. 

      35

    • D. 

      40

  • 10. 
    Allow gtc to run with no load for ___ minutes after on speed light comes on
    • A. 

      2

    • B. 

      3

    • C. 

      1

    • D. 

      4

  • 11. 
    What is the minimum amount of bleed air pressure allowed on the manifold presseure guage 
    • A. 

      Depends on ambient air temp

    • B. 

      Depends on barometric press and ambient temp

    • C. 

      Depends on altitude

    • D. 

      35

  • 12. 
    When doing a bleed down check what is the minimum amount of seconds allowed
    • A. 

      16

    • B. 

      10

    • C. 

      8.5

    • D. 

      9.5

  • 13. 
    Where is the gtc oil tank located 
    • A. 

      Forward left side of the cargo compartment

    • B. 

      Forward right side of the cargo compartment

    • C. 

      Left wheel well area

    • D. 

      Right wheel well area

  • 14. 
    How many quarts of oil are in the entire gtc system
    • A. 

      2

    • B. 

      4

    • C. 

      3

    • D. 

      5

  • 15. 
    The fire protection system runs off of what bus
    • A. 

      Isolated dc

    • B. 

      Essential dc

    • C. 

      Battery

    • D. 

      Main dc

  • 16. 
    If there is a possiblity there is air in the oil system what should you do
    • A. 

      Pump the primer button

    • B. 

      Press the primer button

    • C. 

      Adjust the oil press button

    • D. 

      Adjust oil pressure

  • 17. 
    Where does the fuel for the gtc come from
    • A. 

      #2 engine

    • B. 

      #2 tank

    • C. 

      Crossfeed manifold

    • D. 

      Fuel truck

  • 18. 
    Why must you clear all four props prior to pressurizing the bleed air manifold?
    • A. 

      Props may rotate if an engine start valve has failed in the open position

    • B. 

      In case engine bleed air valve is stuck open

    • C. 

      to prevent harm to personnel

    • D. 

      To prevent damage to equipment

  • 19. 
    How many minutes must you run the gtc w no load before placing the gtc to off 
    • A. 

      1

    • B. 

      2

    • C. 

      3

    • D. 

      4

  • 20. 
    When operating the atm the ac voltimeter should indicate between 
    • A. 

      110-115

    • B. 

      115-120

    • C. 

      112-118

    • D. 

      120-125

  • 21. 
    When operating the atm the frequency meter should indiucate between 
    • A. 

      390-410

    • B. 

      381-410

    • C. 

      380-420

    • D. 

      390-420

  • 22. 
    If using #3 or #4 main tank what must be done before starting the gtc
    • A. 

      Crossfeed primer button pressed

    • B. 

      Crossfeed separation switch to open

    • C. 

      Place tank boost pump on

    • D. 

      Nothing

  • 23. 
    Before operating gtc the wing isolation valve must be in what position
    • A. 

      Open and down

    • B. 

      Open and up

    • C. 

      Closed and down

    • D. 

      Closed and up

  • 24. 
    Before operation gtc and atm place rampd and door control knob to
    • A. 

      3n

    • B. 

      6n

    • C. 

      4n or 6n

    • D. 

      3n or 6n

  • 25. 
    If atm fan is not working what is the atm  gen load restricted to
    • A. 

      .66

    • B. 

      .33

    • C. 

      1.05

    • D. 

      .99

  • 26. 
    To  operat the air conditioning during gtc use place air conditioning master switch to 
    • A. 

      Air bond no press

    • B. 

      Air cond press

    • C. 

      Air cond gtc

    • D. 

      Air cond apu

  • 27. 
    The fuel pressure regulator limits the fuel pressure to the gtc to
    • A. 

      16

    • B. 

      15

    • C. 

      14

    • D. 

      13

  • 28. 
    Approximatly how much il press must be sensed for the gtc to operate 
    • A. 

      4

    • B. 

      2

    • C. 

      5

    • D. 

      3

  • 29. 
    Why must you press the fuel strainer drain valve prior to the first start of the day
    • A. 

      Ensure constant fuel flow

    • B. 

      Verify fuel flow stops

    • C. 

      Verify fuel valve is open

    • D. 

      Gtc won't operate otherwise

  • 30. 
    Before operating gtc inspect inlet for
    • A. 

      Ice

    • B. 

      Fod

    • C. 

      General condition

    • D. 

      All of the above

  • 31. 
    If start light does not go out in one minute place gtc control switch to
    • A. 

      Run

    • B. 

      Restart

    • C. 

      Off

    • D. 

      Stop

  • 32. 
    To operate atm gen place atm gen switch to 
    • A. 

      On

    • B. 

      Normal

    • C. 

      Atm auto

    • D. 

      Atm gen

  • 33. 
    What is the coyote radio freq when establishing comm
    • A. 

      349.5

    • B. 

      339.5

    • C. 

      348.5

    • D. 

      359.5

  • 34. 
    When operating gtc below 32f how long must you allow must you allow the gtc to operate gtc to run before opening manifold 
    • A. 

      2

    • B. 

      3

    • C. 

      5

    • D. 

      4

  • 35. 
    What is the starter duty cycle of the gtc 
    • A. 

      1 on 4 off

    • B. 

      1 on 2 off

    • C. 

      1 on 3 off

    • D. 

      1 on 1 off

  • 36. 
    Where must the ground controller be positioned during operation of the gtc
    • A. 

      Right wheel well area

    • B. 

      Right wing tip

    • C. 

      Left wheel well area

    • D. 

      Left wing tip

  • 37. 
    If required place boost pump on and press croos feed primer button for 
    • A. 

      10

    • B. 

      30

    • C. 

      20

    • D. 

      15

  • 38. 
    If isolated dc is inturrupted what will happen 
    • A. 

      Nothing

    • B. 

      Gtc will flame out

    • C. 

      Gtc will stop

    • D. 

      Gtc door c/b will pop

  • 39. 
    If installed bleed air divider valve should be in what position
    • A. 

      Open

    • B. 

      Closed

    • C. 

      AUTO

    • D. 

      Normal

  • 40. 
    If a rise in leading edge temp is indicated what must be done 
    • A. 

      Emergency shut down procedures

    • B. 

      Shut off gtc

    • C. 

      Close gtc bleed air valve

    • D. 

      Close gtc bleed air valve and shut down gtc

  • 41. 
    When doing a bleed down check when do you start and stop timing 
    • A. 

      30-15

    • B. 

      30-10

    • C. 

      15-30

    • D. 

      10-30

  • 42. 
    When firing the fire bottle do not hold agent discharge switch for more than
    • A. 

      1

    • B. 

      3

    • C. 

      2

    • D. 

      4

  • 43. 
    What could happen if you hold the agent discharge switch for more than the required seconds 
    • A. 

      Trip the fire ext c/b and fire ext system to become inop

    • B. 

      Cause the fire ext system to become inop

    • C. 

      Trip the cb

    • D. 

      All the agent will be discharged

  • 44. 
    If after firing the agent dicharge switch number one and fire persists what must be done 
    • A. 

      Refire no 1

    • B. 

      Place switch to agent no 2 and release

    • C. 

      Have ground controller extinguish fire w halon bottle

    • D. 

      Call fire department

  • 45. 
    Where is the gtc located 
    • A. 

      Forward right wheel well

    • B. 

      Rear left wheel well fairing

    • C. 

      Forward left wheel well fairing

    • D. 

      Rear right wheel well fairing