A Cube Networking Basic Test

15 Questions | Total Attempts: 38

SettingsSettingsSettings
Networking Quizzes & Trivia

Questions and Answers
  • 1. 
    How long is an IPv6 address?
    • A. 

      32 bits

    • B. 

      128 bytes

    • C. 

      64 bits

    • D. 

      128 bits

  • 2. 
    What flavor of Network Address Translation can be used to have one IP address allow many users to connect to the global Internet?
    • A. 

      NAT

    • B. 

      Static

    • C. 

      Dynamic

    • D. 

      PAT

  • 3. 
    What are the two main types of access control lists (ACLs)?
    1. Standard
    2. IEEE
    3. Extended
    4. Specialized
    • A. 

      1 and 3

    • B. 

      2 and 4

    • C. 

      3 and 4

    • D. 

      1 and 2

  • 4. 
    You have 10 users plugged into a hub running 10Mbps half-duplex. There is a server connected to the switch running 10Mbps half-duplex as well. How much bandwidth does each host have to the server?
    • A. 

      100 kbps

    • B. 

      1 Mbps

    • C. 

      2 Mbps

    • D. 

      10 Mbps

  • 5. 
    What command is used to create a backup configuration?
    • A. 

      Copy running backup

    • B. 

      Copy running-config startup-config

    • C. 

      Config mem

    • D. 

      Wr mem

  • 6. 
    Which WLAN IEEE specification allows up to 54Mbps at 2.4GHz?
    • A. 

      A

    • B. 

      B

    • C. 

      G

    • D. 

      N

  • 7. 
    Which of the following is the valid host range for the subnet on which the IP address 192.168.168.188 255.255.255.192 resides?
    • A. 

      192.168.168.129-190

    • B. 

      192.168.168.129-191

    • C. 

      192.168.168.128-190

    • D. 

      192.168.168.128-192

  • 8. 
    What protocol does PPP use to identify the Network layer protocol?
    • A. 

      NCP

    • B. 

      ISDN

    • C. 

      HDLC

    • D. 

      LCP

  • 9. 
    Which of the following commands will allow you to set your Telnet password on a Cisco router?
    • A. 

      Line telnet 0 4

    • B. 

      Line aux 0 4

    • C. 

      Line vty 0 4

    • D. 

      Line con 0

  • 10. 
    Which protocol does DHCP use at the Transport layer?
    • A. 

      IP

    • B. 

      TCP

    • C. 

      UDP

    • D. 

      ARP

  • 11. 
    Which command is used to determine if an IP access list is enabled on a particular interface?
    • A. 

      Show access-lists

    • B. 

      Show interface

    • C. 

      Show ip interface

    • D. 

      Show interface access-lists

  • 12. 
    Where is a hub specified in the OSI model?
    • A. 

      Session layer

    • B. 

      Physical layer

    • C. 

      Data Link layer

    • D. 

      Application layer

  • 13. 
    Which protocol is used to send a destination network unknown message back to originating hosts?
    • A. 

      TCP

    • B. 

      ARP

    • C. 

      ICMP

    • D. 

      BootP

  • 14. 
    How many broadcast domains are created when you segment a network with a 12-port switch?
    • A. 

      1

    • B. 

      2

    • C. 

      5

    • D. 

      12

  • 15. 
    Which router command allows you to view the entire contents of all access lists?
    • A. 

      Show all access-lists

    • B. 

      Show access-lists

    • C. 

      Show ip interface

    • D. 

      Show interface

Back to Top Back to top