2A655 Study Guide
- 1.
Generally speaking, if you're working in-shop at a regular operational base, what type of maintenance are you performing?
- A.
Organizational
- B.
Intermediate
- C.
Depot-level
- D.
Two-Level
Correct Answer
B. Intermediate -
- 2.
In the Air Combat Command (ACC) objective wing, where is most of the off-equipment overhauling and in-shop work done?
- A.
Support Group
- B.
Logistics Group
- C.
Objective Group
- D.
Operations Group
Correct Answer
B. Logistics Group -
- 3.
Which squadron is the direct sortie producing function within the operations group?
- A.
Operations Squadron
- B.
Maintenance squadron
- C.
Component repair squadron
- D.
Equipment maintenance squadron
Correct Answer
A. Operations Squadron -
- 4.
In Air Mobility Command (AMC), the flightline maintenance is a part of which group?
- A.
Support
- B.
Logistics
- C.
Operations
- D.
Either operations or logistics
Correct Answer
D. Either operations or logistics -
- 5.
Under the production team maintenance concept, flightline work is done the
- A.
Accessories flight
- B.
Maintenance squadron
- C.
Sortie generation flight
- D.
Equipment maintenance squadron
Correct Answer
C. Sortie generation flight -
- 6.
WHich subsystem of CAMS provides the capability to establish a computerized file of required maintenance actions?
- A.
Maintenance events
- B.
Operational events
- C.
Inquiries and reports
- D.
Maintenance personnel
Correct Answer
A. Maintenance events -
- 7.
The Operational Events subsystem of CAMS has three phases. Which phase would give you data relating to aborts, cancellations, late take-offs or delays?
- A.
Analysis
- B.
Location
- C.
Mission Recording
- D.
Mission Accomplishment
Correct Answer
A. Analysis -
- 8.
When the new AFTO form 781A is initiated, what kind of discrepancies cannont be transferred to the AFTO form 781K?
- A.
Red X
- B.
Red /
- C.
Red -
- D.
Discrepancies with a supply document #
Correct Answer
A. Red X -
- 9.
Which aircraft periodic inspection is used to detect defects that could have developed during ground operation of an aircraft?
- A.
Pre flight
- B.
Thru flight
- C.
Post flight
- D.
End of runway
Correct Answer
D. End of runway -
- 10.
Reducing the time an aircraft is out of commission is an objective of which inspection?
- A.
Phase
- B.
Hourly
- C.
Periodic
- D.
Isochronal
Correct Answer
A. Phase -
- 11.
A Category II deficiency report submitted for a defect in workmanship must be forwarded to the orginating point within how many work days?
- A.
1
- B.
2
- C.
3
- D.
4
Correct Answer
C. 3 -
- 12.
Once a defect is identified for a Category I deficiency, the orginator must forward the draft report to the orginating point within?
- A.
12
- B.
24
- C.
48
- D.
72
Correct Answer
B. 24 -
- 13.
What is the first part of the national stock number indicate?
- A.
Part code
- B.
Bureau code
- C.
Item identification
- D.
Supply classification
Correct Answer
D. Supply classification -
- 14.
Normally shop stock usage should not exceed how many days?
- A.
30
- B.
60
- C.
90
- D.
120
Correct Answer
C. 90 -
- 15.
While conducting an inventory of bench stock, you notice a due out card in one of the bins. What does this indicate?
- A.
Part has been deleted
- B.
Part is already on order
- C.
Quantity is below 50%
- D.
Part is sub-located to a different bin
Correct Answer
B. Part is already on order -
- 16.
What form does supply use for a due-in form maintenance (DFIM) notice?
- A.
DD Form 1348-1
- B.
AF Form 2413
- C.
DD form 1348-6
- D.
AFTO form 350 tag
Correct Answer
A. DD Form 1348-1 -
- 17.
Before an item is issued from supply demand processing must have certain information recorded on an AF Form
- A.
1297
- B.
2004
- C.
2005
- D.
2413
Correct Answer
C. 2005 -
- 18.
Which supply condition tag would be attached to a part that has been repaired for turn-in to supply?
- A.
DD form 1297
- B.
Dd form 1574
- C.
Dd form 1577
- D.
Dd form 1577-2
Correct Answer
B. Dd form 1574 -
- 19.
What types of property responsibility can be charged to air force personnel?
- A.
Custodial & individual
- B.
Command & custodial
- C.
Individual & supervisory
- D.
Command & supervisory
Correct Answer
B. Command & custodial -
- 20.
Who is responsible for the Depot Level Reparables Program?
- A.
Base supply
- B.
Maintenance units
- C.
Unit resource advisor
- D.
Reparable support division
Correct Answer
D. Reparable support division -
- 21.
Which TO tells us how to maintain particular weapon systems?
- A.
Technical manual
- B.
Abbreviated technical order
- C.
TCTO
- D.
Methods & procedures TO
Correct Answer
A. Technical manual -
- 22.
A series of red Xs is printed around the border of the first page of a TCTO signifies which type of TCTO?
- A.
Urgent
- B.
Routine
- C.
Immediate
- D.
Inspection
Correct Answer
C. Immediate -
- 23.
In the basic TO numbering system, each TO number has a minimum of how many number groups?
- A.
2
- B.
3
- C.
4
- D.
5
Correct Answer
B. 3 -
- 24.
Which MIDAS TO number group describes the type of TO?
- A.
First
- B.
Second
- C.
Third
- D.
Fourth
Correct Answer
C. Third -
- 25.
Using the MIDAS TO system, which TO would you use to find a brief description of an aircraft's system or subsystem?
- A.
Job guide manual
- B.
General vehicle manual
- C.
General systems manual
- D.
Schematic diagram manual
Correct Answer
B. General vehicle manual -
- 26.
Revisions are normally made instead of changes when the basic TO consists of
- A.
8 pages or less
- B.
8 pages or more
- C.
9 pages
- D.
10 pages
Correct Answer
A. 8 pages or less -
- 27.
What percentage of accidents are caused by nature?
- A.
2%
- B.
4%
- C.
6%
- D.
8%
Correct Answer
A. 2% -
- 28.
When temporarily allowing a potentially dangerous condition to exist, you must
- A.
Post warning signs
- B.
Brief all personnel
- C.
Inform the commander
- D.
Call the base safety office
Correct Answer
A. Post warning signs -
- 29.
How is an oil free nitrogen bottle identified?
- A.
2 inch black band around the shoulder
- B.
3 inch black band around the shoulder
- C.
2x2inch black bands around the shoulder
- D.
2x 3inch black bands around the shoulder
Correct Answer
D. 2x 3inch black bands around the shoulder -
- 30.
Ejection seat safety pins are initially installed
- A.
Prior to entering the cockpit
- B.
Immediately after each flight
- C.
Immediately before each flight
- D.
When performing maintenance in the cockpit
Correct Answer
B. Immediately after each flight -
- 31.
Which AFI outlines the Nuclear Surety Program?
- A.
AFI 91-101
- B.
AFI 91-102
- C.
AFI 91-201
- D.
AFI 91-202
Correct Answer
A. AFI 91-101 -
- 32.
How many minimum safety standards are established for nuclear weapons and systems?
- A.
1
- B.
2
- C.
3
- D.
Four
Correct Answer
C. 3 -
- 33.
What terms are used to describe the physical qualities of fluids?
- A.
Resistance , force, and energy
- B.
Incompressibility, resistance, and pressure transmission
- C.
Expansion, contraction, pressure transmission, and resistance
- D.
Pressure transmission , incompressability , expansion, and contraction
Correct Answer
D. Pressure transmission , incompressability , expansion, and contraction -
- 34.
Who said " all gases expand and contract in direct proportion to the change in temperature, provided the pressure is constant?
- A.
Boyle
- B.
Charles
- C.
Pascal
- D.
Bernoulli
Correct Answer
B. Charles -
- 35.
What is the volume of a cylinder 5in high with a 1in radius?
- A.
1.57 cubic in
- B.
3.14 cu in
- C.
15.7 cu in
- D.
31.4 cu in
Correct Answer
C. 15.7 cu in -
- 36.
What would be the volume of fluid displaced if an actuator with a 3-square inch piston moves a distance of 12 inches?
- A.
4 cu in
- B.
12 cu in
- C.
24 cu in
- D.
36 cu in
Correct Answer
D. 36 cu in -
- 37.
To obtain mechanical advantage use the formula , mechanical advantage equals?
- A.
Pressure times volume
- B.
Resistance divided by effort
- C.
Pi times radius squared
- D.
Equals force plus effort
Correct Answer
B. Resistance divided by effort -
- 38.
In the metric system all units are divisable by
- A.
5
- B.
10
- C.
50
- D.
100
Correct Answer
B. 10 -
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Jan 17, 2013Quiz Edited by
ProProfs Editorial Team -
Sep 01, 2010Quiz Created by
Jharris110
Back to top