2008net Module 2

10 Questions | Total Attempts: 32

SettingsSettingsSettings
Please wait...
Module Quizzes & Trivia

2008NET Module 2


Questions and Answers
  • 1. 
    Your network contains a single Active Directory domain. All servers run Windows Server 2008 R2. A DHCP server is deployed on the network and configured to provide IPv6 prefixes. You need to ensure that when you monitor network traffic, you see the interface identifiers derived from the Extended Unique Identifier (EUI)-64 address. Which command should you run?
    • A. 

      Netsh.exe interface ipv6 set global addressmaskreply=disabled

    • B. 

      Netsh.exe interface ipv6 set global dhcpmediasense=enabled

    • C. 

      Netsh.exe interface ipv6 set global randomizeidentifiers=disabled

    • D. 

      Netsh.exe interface ipv6 set privacy state=enabled

  • 2. 
    Your company has four DNS servers that run Windows Server 2008 R2. Each server has a static IP address. You need to prevent DHCP from assigning the addresses of the DNS servers to DHCP clients. What should you do?
    • A. 

      Create a new scope for the DNS servers.

    • B. 

      Create a reservation for the DHCP server.

    • C. 

      Configure the 005 Name Servers scope option.

    • D. 

      Configure an exclusion that contains the IP addresses of the four DNS servers.

  • 3. 
    You have a DHCP server named Server1 and an application server named Server2. Both servers run Windows Server 2008 R2. The DHCP server contains one scope. You need to ensure that Server2 always receives the same IP address. Server2 must receive its DNS settings and its WINS settings from DHCP. What should you do?
    • A. 

      Create a multicast scope.

    • B. 

      Assign a static IP address to Server2.

    • C. 

      Create an exclusion range in the DHCP scope.

    • D. 

      Create a DHCP reservation in the DHCP scope.

  • 4. 
    You have a DHCP server that runs Windows Server 2008 R2. You need to reduce the size of the DHCP database. What should you do?
    • A. 

      From the DHCP snap-in, reconcile the database.

    • B. 

      From the folder that contains the DHCP database, run jetpack.exe dhcp.mdb temp.mdb.

    • C. 

      From the properties of the dhcp.mdb file, enable the File is ready for archiving attribute.

    • D. 

      From the properties of the dhcp.mdb file, enable the Compress contents to save disk space attribute.

  • 5. 
    You have a DHCP server that runs Windows Server 2008 R2. The DHCP server has two network connections named LAN1 and LAN2. You need to prevent the DHCP server from responding to DHCP client requests on LAN2. The server must continue to respond to non-DHCP client requests on LAN2. What should you do?
    • A. 

      From the DHCP snap-in, modify the bindings to associate only LAN1 with the DHCP service.

    • B. 

      From the DHCP snap-in, create a new multicast scope.

    • C. 

      From the properties of the LAN1 network connection, set the metric value to 1.

    • D. 

      From the properties of the LAN2 network connection, set the metric value to 1.

  • 6. 
    You have a DHCP server that runs Windows Server 2008 R2. You restore the DHCP database by using a recent backup. You need to prevent DHCP clients from receiving IP addresses that are currently in use on the network. What should you do?
    • A. 

      Add the DHCP server option 15.

    • B. 

      Add the DHCP server option 44.

    • C. 

      Set the Conflict Detection value to 0.

    • D. 

      Set the Conflict Detection value to 2.

  • 7. 
    Your network uses IPv4. You install a server that runs Windows Server 2008 R2 at a branch office. The server is configured with two network interfaces.   You need to configure routing on the server at the branch office. Which two actions should you perform? (Each correct answer presents part of the solution. Choose two.)
    • A. 

      Install the Routing and Remote Access Services role service.

    • B. 

      Run the netsh ras ip set access ALL command.

    • C. 

      Run the netsh interface ipv4 enable command.

    • D. 

      Enable the IPv4 Router Routing and Remote Access option.

  • 8. 
    Your network contains one Active Directory domain. You have a member server that runs Windows Server 2008 R2.   You need to immediately disable all incoming connections to the server. What should you do?
    • A. 

      From the Services snap-in, disable the IP Helper.

    • B. 

      From the Services snap-in, disable the Netlogon service.

    • C. 

      From Windows Firewall, enable the Block all connections option on the Public Profile.

    • D. 

      From Windows Firewall, enable the Block all connections option on the Domain Profile.

  • 9. 
    You have a DHCP server that runs Windows Server 2008 R2. The DHCP server has two network connections named LAN1 and LAN2. You need to prevent the DHCP server from responding to DHCP client requests on LAN2. The server must continue to respond to non-DHCP client requests on LAN2. What should you do?
    • A. 

      From the DHCP snap-in, modify the bindings to associate only LAN1 with the DHCP service.

    • B. 

      From the DHCP snap-in, create a new multicast scope.

    • C. 

      From the properties of the LAN1 network connection, set the metric value to 1.

    • D. 

      From the properties of the LAN2 network connection, set the metric value to 1.

  • 10. 
    Your company has a server named Server1 that runs Windows Server 2008 R2. Server1 runs the DHCP Server server role and the DNS Server server role. You also have a server named ServerCore that runs a Server Core installation of Windows Server 2008 R2. All computers are configured to use only Server1 for DNS resolution. The IP address of Server1 is 192.168.0.1. The network interface on all the computers is named LAN. Server1 is temporarily offline. A new DNS server named Server2 has been configured to use the IP address 192.168.0.254. You need to configure ServerCore to use Server2 as the preferred DNS server and Server1 as the alternate DNS server. What should you do?
    • A. 

      Run the netsh interface ipv4 add dnsserver "LAN" static 192.168.0.254 index=1 command.

    • B. 

      Run the netsh interface ipv4 set dnsserver "LAN" static 192.168.0.254 192.168.0.1 both command.

    • C. 

      Run the netsh interface ipv4 set dnsserver "LAN" static 192.168.0.254 primary command and the netsh interface ipv4 set dnsserver "LAN" static 192.168.0.1 both command.

    • D. 

      Run the netsh interface ipv4 set dnsserver "LAN" static 192.168.0.254 primary command and the netsh interface ipv4 add dnsserver "LAN" static 192.168.0.1 index=1 command.