7 replies to this topic

[brian10]

file:///C:/Users/Admin/AppData/Local/Temp/msohtmlclip1/01/clip_image002.jpg

PPoE
Layer 2 - PPoE
-configure PPPoE between R3-R4
-configure r3 (or r4) as the PPPoE server
-configure r4 (or r3) as the PPPoE client
-ensure r4 always gets the same IP address, cannot use DHCP
-ensure no interleaving in PPPoE
-there were one or two more PPPoE options required, but forgot
  









Section 1.4
-etherchannel configuration between SW1 and SW2 by using standard protocol , port fa0/24 should be selected as active port
-load-balance hash of source-destination mac address

PART 2
At the beginning , There was important note said;
• Finally, R3 should be able to ping all subnets and loopback0 of routers and switch, all loopback interface must to be seen /32
Layer 3 - OSPF
• in case R1/R5 goes down, ensure R4 can still reach all OSPF networks via R3 // virtual-links from R3 to R5 and R1 ???
2.2 EIGRP
eigrp yy and eigrp 100
no auto-summary

2.3  RIPv2
rip updates only as per topology
redistribute ospf into rip:
R4 must prefer R5 for routes to Sw1 l0
all other routes to go through r3
-redistribute OSPF routes into RIP in R5
-ensure R4 accesses SW1 Lo0 via R5 but all other routes should go through R3
2.4: Redistribute ospf int eigrp yy
R2 and R3 must have only external Eigrp routes from BB3 and the vlan 300 nework all other yy.yy.0.0/16 not in the eigrpyy domain must be seen as ext ospf route by R2 and R3


i only remember so much sorry i passed ts but failed lab

will be going soon this month again in the end

if any 1 intrested can join in here to discuss

Attached Files

•  lab7.jpg   271.09K   31 downloads

[brian10]

brian10, on 01 May 2012 - 08:49 AM, said:

file:///C:/Users/Admin/AppData/Local/Temp/msohtmlclip1/01/clip_image002.jpg

PPoE
Layer 2 - PPoE
-configure PPPoE between R3-R4
-configure r3 (or r4) as the PPPoE server
-configure r4 (or r3) as the PPPoE client
-ensure r4 always gets the same IP address, cannot use DHCP
-ensure no interleaving in PPPoE
-there were one or two more PPPoE options required, but forgot
  









Section 1.4
-etherchannel configuration between SW1 and SW2 by using standard protocol , port fa0/24 should be selected as active port
-load-balance hash of source-destination mac address

PART 2
At the beginning , There was important note said;
• Finally, R3 should be able to ping all subnets and loopback0 of routers and switch, all loopback interface must to be seen /32
Layer 3 - OSPF
• in case R1/R5 goes down, ensure R4 can still reach all OSPF networks via R3 // virtual-links from R3 to R5 and R1 ???
2.2 EIGRP
eigrp yy and eigrp 100
no auto-summary

2.3  RIPv2
rip updates only as per topology
redistribute ospf into rip:
R4 must prefer R5 for routes to Sw1 l0
all other routes to go through r3
-redistribute OSPF routes into RIP in R5
-ensure R4 accesses SW1 Lo0 via R5 but all other routes should go through R3
2.4: Redistribute ospf int eigrp yy
R2 and R3 must have only external Eigrp routes from BB3 and the vlan 300 nework all other yy.yy.0.0/16 not in the eigrpyy domain must be seen as ext ospf route by R2 and R3


i only remember so much sorry i passed ts but failed lab

will be going soon this month again in the end

if any 1 intrested can join in here to discuss

hi


guys can add me on [email protected]

[CCIE_Pro]

The same thing happen to me 48hrs ago. Maybe we can team together.

[brian10]

Hi

thats the reason i am asking u guys ur skype or gmail id cause i already created a group of 25 ccie

if we could be more it will be good for us

CCIE_Pro, on 02 May 2012 - 06:24 AM, said:

The same thing happen to me 48hrs ago. Maybe we can team together.

[ieeu]

my email id is deepakjanju[email protected]

it would be nice to be a a part of this. Please add me.

brian10, on 01 May 2012 - 08:49 AM, said:

file:///C:/Users/Admin/AppData/Local/Temp/msohtmlclip1/01/clip_image002.jpg

PPoE
Layer 2 - PPoE
-configure PPPoE between R3-R4
-configure r3 (or r4) as the PPPoE server
-configure r4 (or r3) as the PPPoE client
-ensure r4 always gets the same IP address, cannot use DHCP
-ensure no interleaving in PPPoE
-there were one or two more PPPoE options required, but forgot
  









Section 1.4
-etherchannel configuration between SW1 and SW2 by using standard protocol , port fa0/24 should be selected as active port
-load-balance hash of source-destination mac address

PART 2
At the beginning , There was important note said;
• Finally, R3 should be able to ping all subnets and loopback0 of routers and switch, all loopback interface must to be seen /32
Layer 3 - OSPF
• in case R1/R5 goes down, ensure R4 can still reach all OSPF networks via R3 // virtual-links from R3 to R5 and R1 ???
2.2 EIGRP
eigrp yy and eigrp 100
no auto-summary

2.3  RIPv2
rip updates only as per topology
redistribute ospf into rip:
R4 must prefer R5 for routes to Sw1 l0
all other routes to go through r3
-redistribute OSPF routes into RIP in R5
-ensure R4 accesses SW1 Lo0 via R5 but all other routes should go through R3
2.4: Redistribute ospf int eigrp yy
R2 and R3 must have only external Eigrp routes from BB3 and the vlan 300 nework all other yy.yy.0.0/16 not in the eigrpyy domain must be seen as ext ospf route by R2 and R3


i only remember so much sorry i passed ts but failed lab

will be going soon this month again in the end

if any 1 intrested can join in here to discuss

[annafra]

..

Edited by annafra, 29 May 2012 - 05:10 AM.

[annafra]

some more options for the PPoE
- Do not use the ppp chap hostname command on R3
- Use CISCO as CHAP password for R3
- Make sure that all CHAP passwords are shown in clear in the configuration

[wode]

Hello guys,

Nice initiative. I will like to be part of this group. Pls add [email protected] I have my exam in few weeks time.